Nuno Miranda

Nuno Miranda

Auto-generated profile, based on publicly available information

Nuno Miranda

ESA-ESRIN, Via Galileo Galilei, 00044 Frascati, Italy

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 July 2015 in Remote Sensing
Verified
Journal Article
Open access
PDF file
ASAdrian Schubert
Adrian Schubert
DSDavid Small
David Small
NMNuno Miranda
Nuno Miranda
DGDirk Geudtner
Dirk Geudtner
EMErich Meier
Erich Meier
Sentinel-1A (S1A) is an Earth observation satellite carrying a state-of-the-art Synthetic Aperture Radar (SAR) imaging instrument. It was launched by the European Space Agency (ESA) on 3 April 2014. With the end of the in-orbit commissioning phase having been completed at the end of September 2014, S1A data products are already consistently providing highly accurate geolocation. StripMap (SM) mode products were acquired regularly and tested for geolocation accuracy and consistency during dedicated corner reflector (CR) campaigns. At the completion of this phase, small geometric inconsistencies had been understood and mitigated, with the high quality of the final product geolocation estimates reflecting the mission’s success thus far. This paper describes the measurement campaign, the methods used during geolocation estimation, and presents best estimates of the product Absolute Location Error (ALE) available at the beginning of S1A’s operational phase.

14 June 2017 in Remote Sensing
Verified
Journal Article
Open access
PDF file
ASAdrian Schubert
Adrian Schubert
NMNuno Miranda
Nuno Miranda
DGDirk Geudtner
Dirk Geudtner
DSDavid Small
David Small
Sentinel-1A and -1B are twin spaceborne synthetic aperture radar (SAR) sensors developed and operated by the European Space Agency under the auspices of the Copernicus Earth observation programme. Launched in April 2014 and April 2016, Sentinel-1A and -1B are currently operating in tandem, in a common orbital configuration to provide an increased revisit frequency. In-orbit commissioning was completed for each unit within months of their respective launches, and level-1 SAR products generated by the operational SAR processor have been geometrically calibrated. In order to compare and monitor the geometric characteristics of the level-1 products from both units, as well as to investigate potential improvements, products from both satellites have been monitored since their respective commissioning phases. In this study, we present geolocation accuracy estimates for both Sentinel-1 units based on the time series of level-1 products collected thus far. While both units were demonstrated to be performing consistently, and providing SAR data products according to the nominal product specifications, a subtle beam- and mode-dependent azimuth bias common to the data from both units was identified. A method for removing the bias is proposed, and the corresponding improvement to the geometric accuracies is demonstrated and quantified.

11 June 2020 in IEEE Transactions on Geoscience and Remote Sensing
Verified
Journal Article
Open access
CGChristoph Gisinger
Christoph Gisinger
ASAdrian Schubert
Adrian Schubert
HBHelko Breit
Helko Breit
MGMatthew Garthwaite
Matthew Garthwaite
UBUlrich Balss
Ulrich Balss
NMNuno Miranda
Nuno Miranda
This article shows how the array of corner reflectors (CRs) in Queensland, Australia, together with highly accurate geodetic synthetic aperture radar (SAR) techniques--also called imaging geodesy--can be used to measure the absolute and relative geometric fidelity of SAR missions. We describe, in detail, the end-to-end methodology and apply it to TerraSAR-X TerraSAR-X Stripmap (SM) and ScanSAR (SC) data and to Sentinel-1 interferometric wide swath (IW) data. Geometric distortions within images that are caused by commonly used SAR processor approximations are explained, and we show how to correct them during postprocessing. Our results, supported by the analysis of 140 images across the different SAR modes and using the 40 reflectors of the array, confirm our methodology and achieve the limits predicted by theory for both Sentinel-1 and TerraSAR-X. After our corrections, the Sentinel-1 residual errors are 6 cm in range and 26 cm in azimuth, including all error sources. The findings are confirmed by the mutual independent processing carried out at University of Zurich (UZH) and German Aerospace Center (DLR). This represents an improvement of the geolocation accuracy by approximately a factor of four in range and a factor of two in azimuth compared with the standard Sentinel-1 products. The TerraSAR-X results are even better. The achieved geolocation accuracy now approaches that of the global navigation satellite system (GNSS)-based survey of the CRs positions, which highlights the potential of the end-to-end SAR methodology for imaging geodesy.

25 November 2021 in IEEE Transactions on Geoscience and Remote Sensing
Verified
Journal Article
Open access
AKAnton Korosov
Anton Korosov
DDDenis Demchev
Denis Demchev
NMNuno Miranda
Nuno Miranda
NFNiccolo Franceschi
Niccolo Franceschi
JPJeong-Won Park
Jeong-Won Park
An updated algorithm for the removal of thermal noise in Sentinel-1 synthetic aperture radar (SAR) level-1 ground range detected (GRD) data in cross-polarization is presented. The algorithm is comprised of two steps: correction of the annotated thermal noise magnitude (previously proposed in Park et al. , 2018) and a novel correction of the annotated thermal noise range dependence. The magnitude of the annotated thermal noise is corrected by applying scale and offset coefficients tuned on a few hundred of Sentinel-1 data acquired over surfaces with low backscatter in interferometric wide and extra-wide swath modes in HV and VH polarizations. The values of coefficients for all modes and polarizations for data processing with the Instrument Processing Facility (IPF) version 3.1–3.3 are provided. The range dependence is corrected by minimizing a cost function between the annotated range profiles of thermal noise and antenna pattern gain (APG). An objective validation metric based on a comparison of averaged backscatter at interswath boundaries is proposed. Validation is performed on hundreds of Sentinel-1 scenes acquired over the open ocean, doldrums, deserts, and sea ice. It shows that the new algorithm outperforms the standard thermal noise removal algorithm proposed by European Space Agency in almost all cases. Analysis shows that the new algorithm worsens noise correction in cases when the range dependence of the annotated APG does not match with the observed signal, indicating either problems with signal processing on IPF or imprecise annotation of APG.

27 July 2022 in IEEE Transactions on Geoscience and Remote Sensing
Verified
Journal Article
Open access
CGChristoph Gisinger
Christoph Gisinger
LLLudivine Libert
Ludivine Libert
PMPetar Marinkovic
Petar Marinkovic
LKLukas Krieger
Lukas Krieger
YLYngvar Larsen
Yngvar Larsen
NMNuno Miranda
Nuno Miranda
This article introduces the extended timing annotation dataset (ETAD) product for Sentinel-1 (S-1) which was developed in a joint effort of German Aerospace Center (DLR) and European Space Agency (ESA). It allows to correct range and azimuth timing of S-1 images for geophysical effects and for inaccuracies in synthetic aperture radar (SAR) image focusing. In combination with the precise orbit solution, these effects determine the absolute geolocation accuracy of S-1 SAR images and the relative collocation accuracy of repeat pass image stacks. ETAD contains the gridded timing corrections for the tropospheric and ionospheric path delays, the tidal-based surface displacements, and the SAR processing effects, all of which are computed for each data taken using standard models from geodesy and auxiliary atmospheric data. The ETAD product helps S-1 users to significantly improve the geolocation accuracy of the S-1 SAR products to better than 0.2 m and offers a potential solution for correcting large-scale interferometric phase variations. The product layout and product generation are described schematically. This article also reports first the results for different SAR techniques: first, the improvement in geolocation accuracy down to a few centimeters by verification of accurately surveyed corner reflector positions in the range–azimuth plane; second, the well-established offset-tracking technique, which is used for systematic ice velocity monitoring of ice sheets and glaciers, where ETAD can reduce velocity biases down to subcentimetric values; and third, the correction of atmospheric phase contributions in wide-area interferograms used for national and European ground motion services. These early results proof the added value of the ETAD corrections and that the product design is well-suited to be integrated into the processing flows of established SAR applications such as absolute ranging of targets, speckle/feature tracking, and interferometry.

11 February 2021 in IEEE Transactions on Geoscience and Remote Sensing
Verified
Journal Article
Open access
DSDavid Small
David Small
CRChristoph Rohner
Christoph Rohner
NMNuno Miranda
Nuno Miranda
MRMarius Ruetschi
Marius Ruetschi
XXXxx Xxx
Xxx Xxx
The benefits of composite products are well known to users of data from optical sensors: cloud-cleared composite reflectance or index products are commonly used as an analysis-ready data (ARD) layer. No analogous composite products are currently in widespread use that is based on spaceborne radar satellite backscatter signals. Here, we present a methodology to produce wide-area ARD composite backscatter images. They build on the existing heritage of geometrically and radiometrically terrain corrected level 1 products. By combining backscatter measurements of a single region seen from multiple satellite tracks (incl. ascending and descending), they are able to provide wide-area coverage with low latency. The analysis-ready composite backscatter maps provide flattened backscatter estimates that are geometrically and radiometrically corrected for slope effects. A mask layer annotating the local quality of the composite resolution is introduced. Multiple tracks are combined by weighting each observation by its local resolution, generating seamless wide-area backscatter maps suitable for applications ranging from wet snow monitoring to land cover classification or short-term change detection.