1 August 2019 in Renewable Energy
PNPablo Sampaio Gomes Natividade
Pablo Sampaio Gomes Natividade
GMGabriel de Moraes Moura
RGRogério Valentim Gelamo
JGJúlio Cesar de Souza Inácio Gonçalves
Júlio Cesar de Souza Inácio Gonçalves
5 August 2016 in International Journal of Energy and Environmental Engineering
This work aims to build a monitoring thermal system based on low cost and using the Arduino MEGA platform. To the temperature, measurements are used thirty (30) digital sensors (DS18B20 Dallas) boarded together using three (3) wires, therefore, requiring the “One Wire” library to allow a correct read in the Arduino software. Using the Dallas sensors and the Arduino programming, it is possible monitoring the temperatures of up to 100 and twenty (120) different points, thereby significantly reducing electric problems and also the diameter of the thermal probe from uses only three (3) wires. The use of thirty (30) digital sensors significantly reduces the electrical problems and increases the processing speed using the multiplexing through the electrical connection to three (3) wires, called “normal power mode”. Using the thermal probe, which is installed, vertically inside the reservoir, it is possible to obtain the temperature graphical points, thus allowing the analysis of thermal stratification. The software used is Arduino IDE based in a language called CCS (C, C++ and “Wiring”). The water inside the reservoir stores energy in the form of sensible heat, based on the importance of the thermodynamics analysis result for this research, therefore, with some temperature, data samples obtained in thermal probe are possible to analyze the thermal stratification in the reservoir. The thermal efficiency of the energy stored in the water, either thermally stratified or homogeneous, analyzed to the first law of thermodynamics, it is the same. In the case of the second law of thermodynamics, the heat efficiency to heat homogenized water is less than the thermal efficiency in the stored water thermally stratified in the reservoir and both of them are lower than the first law of thermodynamics.
1 March 2018 in International Journal of Thermodynamics
Thermal Pyranometers are very important devices for evaluating the intensity of solar radiation under different climatic conditions. These devices utilize thermal radiation for comparison and determination of their efficiency. Because of this wide use associated with the development of new technologies, a simple and low-cost version of thermal pyranometer has been studied, designed and manufactured. A blackened aluminum disk is used as a hot junction, and the cold junction is exposed to ambient air. The two terminals are connected to a digital amplifier with output signal directed to an Arduino board. A device calibration was performed by comparing the results with a commercial photodiode sensor. Statistical analysis of the calibration data considering a 99% confidence level leads to an estimated standard error of 20.8 W/m². An analysis of its response time also estimated from a dynamic model. This model uses a numerical solution of the energy balance on heat exchange between the aluminum disc and the environment. The instrument response time based on the average of the estimates obtained from the dynamic model is about 1.5 minutes. Based on these studies it was concluded that the characteristics of the sensor are adequate for most solar energy tests and the final cost of US $ 60.00 is much lower than the large majority of such commercial devices.
1 December 2018 in Ingeniare. Revista chilena de ingeniería
Continuous tunnel furnace has greater flexibility in heating and high productivity and it was becoming the best option for processing industrialized food products. The main objective of this work is the validation of the results from radiation models viewFactor and FVDOM. In his case, the software OpenFOAM® was used and one of its applications in the evaluation of net rate heat exchanges by radiation on the mat of a real continuous furnace. The geometry, operational conditions, mesh definition, initial and boundary conditions used in the model were obtained from literature data, technical manuals and operational furnaces found in food industries. The implementation and simulation of physical model, in the OpenFOAM® has several simplifying hypothesis highlighting air is treated as an ideal and incompressible, Newtonian and non-participant to the exchanges of heat by radiation; laminar flow viewFactor and FVDOM radiation models; pressure-velocity coupling algorithm SIMPLE. The results obtained were used to validate the radiation models through analytical results and also the convective heat flux. The orders of magnitude between radiation and convection turn it difficult to correctly evaluate the heat flux. Small fluctuations in temperature and velocity affect considerably and induce oscillations on the heat flux results. The viewFactor radiation model was more advantageous due to its greater simplicity and higher convergence velocity.
1 January 2019 in Facta universitatis - series: Electronics and Energetics
PNPablo Sampaio Gomes Natividade
Pablo Sampaio Gomes Natividade
+1
In all studies involving wind speed, such as meteorology, wind turbines and agriculture accurate speed information for decision making is required. There are several types of anemometers, with medium and high costs, such as cup, hot wire and pitot tubes, the hot wire being more sensitive and expensive than others. The device developed in this work is the cup anemometer, that is easy to build. The great advantage of this device is the low cost, with an approximate value of US$ 50.00, using simple materials that are easy to find in commercial stores. The Reed Switch sensor is also another advantage as it does not require a sophisticated programming, as well as the open platform Arduino. The use of theoretical aerodynamic drag coefficients and the presented calculations resulted in values very close to a commercial anemometer. The coefficient of determination between the cup Anemometer and the standard sensor of Meteorological Research Institute IPMet/Brazil is R2=0.9999, indicating strong correlation between the instruments. As the reference anemometer (IPMet) has high embedded technology and the prototype is low cost, we conclude that the project has an attractive cost benefit for possible development and production, reaching the objective of this work.
30 June 2014 in Revista de Engenharia Térmica
The need of renewable energy sources due to climate change and thus the search for clean energy sources, justify the growing investment on new types of solar collectors. The research has contributed to this expansion in the scope of solar concentrator collectors, with the efficiency as the main goal. Many works have been developed in order to optimize the thermal stratification of the fluid inside the tubes and heat reservoirs, as well as mathematical modeling considering the problem as transient heat flow as boundary condition. In this work is studied experimentally, the heating of the water by solar collector modified from the conventional evacuated tube, focusing on efficiency. With the help of CFD software, a theoretical analysis is done to visualize the phenomenon, assuming the same boundary conditions and geometric experimental problem. An important approach concerns the physical separation of the flows of both cold and hot water inside the evacuated tube. The system performance was analyzed using experimental tests performed outdoors with sunlight.