The article proposes new modified Multiply-Accumulate (MAC) units called truncated MAC units and using residue number system (RNS) with moduli of a special form. The effectiveness of the proposed blocks is verified by hardware implementation of digital filtering. The paper presents a comparative theoretical analysis of the proposed approach using the RNS and the known methods using the conventional positional number system (PNS) and RNS. Moreover, in the paper, a hardware simulation on FPGA of digital filters using arithmetic of RNS is performed, and comparison with the known implementations are realized. It is shown that using proposed approach based on RNS makes it possible to increase the frequency of digital filters by about 4 times, and reduce the hardware costs by 3 times, in comparison with the use of the traditional positional number system. Comparison proposed method and known methods based on RNS shows that using proposed method allows to increase the frequency by about 2-6 times, and reduce the hardware costs by 1.5-5 times, with increasing power consumption by 23%. Obtained results open up the possibility for efficient hardware implementation of digital filters on modern devices (FPGA, ASIC, etc.) for solving practical problems such as noise reduction, amplification and suppression of frequencies, interpolation, decimation, equalization, and many others.
Improving the technical characteristics of digital signal processing devices is an important problem in many practical tasks. The paper proposes the architecture of a device for two-dimensional filtering in a residue number system (RNS) with moduli of a special type according to the Winograd method. The work carried out the technical parameters theoretical analysis of the proposed filter architecture for different RNS moduli sets by the “unit-gate”-model. In addition, the proposed architecture is compared with known digital filter implementations. The theoretical analysis results showed that the use of the proposed filter architecture makes it possible to increase the signal processing speed by 1.33 – 6.90 times, in comparison with the known device implementations. Also, in the work, the hardware simulation of the proposed filter architecture was performed on FPGA, which showed that the performance of the proposed device is 1.31 – 4.12 times higher than known digital filter architectures. The research results can be used in digital signal processing systems to increase their performance and reduce hardware costs. In addition, the developed architectures can be applied in the development of hardware accelerators for complex digital signals analysis systems.
Improving the characteristics of digital signal processing devices is an important task in many practical problems. The paper proposes the architecture of a two-dimensional digital filter with a 5×5 mask, in which calculations are performed according to the Winograd method in the Residue Number System (RNS) with moduli of a special type. Theoretical analysis and hardware Field-Programmable Gate Array simulation are presented. The results show that the fragment throughput fr/s (number of fragments per second) of the device is 29.6% – 724.7% higher than state-of-the-art solutions. This is achieved by the combination of the Winograd method, which reduces the number of multiplications, with the RNS arithmetic, which performs addition and multiplication under smaller operands in parallel. However, our experiments showed that the proposed method requires up to 2.54% – 11.01% more Look-Up Tables and 3.58% – 19.83% higher power consumption compared to known analogues.
Сверточные нейронные сети (СНС) показывают высокую точность при решении задачи распознавания образов, но обладают высокой вычислительной сложностью, что приводит к медленной обработке данных. Для увеличения быстродействия СНС в данной работе предлагается метод аппаратной реализации СНС с вычислениями в системе остаточных классов с модулями специального вида и . В статье представлено аппаратное моделирование предлагаемого метода на FPGA на примере СНС LeNet-5, обученной на базах изображений MNIST, FMNIST и CIFAR-10. Моделирование показало, что применение предлагаемого подхода позволяет увеличить тактовую частоту и производительность устройства примерно на 11% –12%, по сравнению с традиционным подходом на основе позиционной системы счисления. Тем не менее, увеличение скорости работы устройства достигнуто за счет увеличения аппаратных затрат. Предлагаемый в статье метод может быть применен системах распознавания образов, когда необходимо обеспечить высокую скорость обработки данных.