In this study, we investigated the influence of thermal treatment, soaking in H2SO4 and electrochemical ageing on commercially available carbon felt materials from SGL carbon. We compared both the influence of the pre-treatment (carbonization or graphitization) and the influence of the precursor (Rayon or PAN). By thermogravimetric analysis coupled with mass spectrometry (TGA-MS) we showed, that after thermal treatment, the thermal stability was lower for carbonized felts compared to graphitized felts and the Rayon based felts were more stable than PAN based ones. Soaking had a stronger impact on the thermal stability of PAN based felts, whereas it was similar to the electrochemical ageing for Rayon based felts. X-ray photoelectron spectroscopy and Raman spectroscopy revealed that thermal treatment reduces the overall surface oxygen content for all felt types and the degree of graphitization doesn't change, but the content of single bonded oxygen was increased for graphitized carbon felts, only. For carbonized felts, thermal treatment highly reduced the electrochemical activity characterized by cyclic voltammetry due to a reduced overall oxygen content and increased C=O and C=C contents. In this work, we provide a comprehensive overview of commercially available carbon felts and characterize the effects of several treatment methods.
Aqueous zinc–air batteries (ZABs) are a low‐cost, safe, and sustainable technology for stationary energy storage. ZABs with pH‐buffered near‐neutral electrolytes have the potential for longer lifetime compared to traditional alkaline ZABs due to the slower absorption of carbonates at nonalkaline pH values. However, existing near‐neutral electrolytes often contain halide salts, which are corrosive and threaten the precipitation of ZnO as the dominant discharge product. This paper presents a method for designing halide‐free aqueous ZAB electrolytes using thermodynamic descriptors to computationally screen components. The dynamic performance of a ZAB with one possible halide‐free aqueous electrolyte based on organic salts is simulated using an advanced method of continuum modeling, and the results are validated by experiments. X‐ray diffraction, scanning electron microscopy, and energy dispersive X‐ray spectroscopy measurements of Zn electrodes show that ZnO is the dominant discharge product, and operando pH measurements confirm the stability of the electrolyte pH during cell cycling. Long‐term full cell cycling tests are performed, and rotating ring disk electrode measurements elucidate the mechanism of oxygen reduction reaction and oxygen evolution reaction. The analysis shows that aqueous electrolytes containing organic salts could be a promising field of research for zinc‐based batteries, due to their Zn2+ chelating and pH buffering properties. The remaining challenges including the electrochemical stability of the electrolyte components are discussed.
Halide‐free, water‐in‐salt electrolytes (WiSEs) composed of potassium acetate (KAc) and zinc acetate (ZnAc2) are investigated as electrolytes in zinc‐ion hybrid supercapacitors (ZHSs). Molecular dynamics simulations demonstrate that water molecules are mostly non‐interacting with each other in the highly concentrated WiSEs, while “bulk‐like water” regions are present in the dilute electrolyte. Among the various concentrated electrolytes investigated, the 30 m KAc and 1 m ZnAc2 electrolyte (30K1Zn) grants the best performance in terms of reversibility and stability of Zn plating/stripping while the less concentrated electrolyte cannot suppress corrosion of Zn and hydrogen evolution. The ZHSs utilizing 30K1Zn, in combination with a commercial activated carbon (AC) positive electrode and Zn as the negative electrode, deliver a capacity of 65 mAh g−1 (based on the AC weight) at a current density of 5 A g−1. They also offer an excellent capacity retention over 10 000 cycles and an impressive coulombic efficiency (≈100%).
1 November 2015 in Electrochemistry Communications
Aiming at a better understanding of correlations between the activity and selectivity of Au electrodes in the oxygen reduction reaction (ORR) under controlled transport conditions, we have investigated this reaction by combined electrochemical and in situ FTIR measurements, performed in a flow cell set‐up in an attenuated total reflection (ATR) configuration in acid and alkaline electrolytes. The formation of incomplete reduction products (hydrogen peroxyde/peroxyls) was detected by a collector electrode, the onset of OHad formation was probed by bulk CO oxidation. Using an electroless‐deposited, annealed Au film on a Si prism as working electrode and three different electrolytes for comparison (sulfuric acid, perchloric acid, sodium hydroxide solution), we could derive detailed information on the anion adsorption behavior, and could correlate this with the ORR characteristics. The data reveal pronounced effects of the anions and the pH on the ORR characteristics, indicated e. g., by a grossly different activity and selectivity for the 4‐electron pathway to water/hydroxyls, with the onset ranging from ca. 1.0 V in alkaline electrolyte to 0.6 V in sulfuric acid electrolyte, and the selectivity for the 4‐electron pathway ranging from 100 % (alkaline electrolyte, low overpotentials) to 40 % (acidic electrolytes, alkaline electrolyte at high overpotentials). In contrast, the effect of the ORR on the anion adsorption characteristics is small. Anion effects as well as correlations between anion adsorption and ORR are discussed.