Esau Abekah Armah

Esau Abekah Armah

Auto-generated profile, based on publicly available information

Esau Abekah Armah

Department of Physics, University of Ghana

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 July 2020 in Advanced Nano Research
Verified
Journal Article
Open access
PDF file
EAEsau Nii Abekah Akwetey Armah
Esau Nii Abekah Akwetey Armah
MEMartin Egblewogbe
Martin Egblewogbe
HKHubert Azoda Koffi
Hubert Azoda Koffi
AYAlfred Ato Yankson
Alfred Ato Yankson
FAFrancis Kofi Ampong
Francis Kofi Ampong
RNRobert Kwame Nkum
Robert Kwame Nkum
Powder samples of Zn1-xMnxO nanocrystal were synthesized at a temperature of 200 °C using solid phase method. Dopant concentrations of 0.005 ≤ x ≤ 0.5 were studied. Powder x-ray diffraction (PXRD) patterns of the samples were analyzed with a view of determining the onset of secondary phases, hence the solubility limit of the dopant. The solubility limit for Mn in ZnO samples synthesized at 200 °C is realized at x < 0.3. With a regular pattern in increment of the Mn concentration, there were variations observed in the trend of the relative intensity, 2θ position and d-spacing indicating uneven addition of Mn (thus Mn2+, Mn3+ or Mn4+).

6 April 2023 in Advanced Nano Research
Verified
Journal Article
Open access
PDF file
NANii Abekah Akwetey Armah
Nii Abekah Akwetey Armah
HKHubert Azoda Koffi
Hubert Azoda Koffi
Transparent conducting oxide material, ZnO nanoparticles has been synthesized using inexpensive and eco-friendly synthesis procedures with less or environmental pollutants and no liquid waste products. The effect of the temperatures on the structural properties for the synthesized ZnO nanocrystals has been investigated. In this study, we report an easy, low-cost, re-producible method for synthesizing ZnO nanoparticles by means of the liquid phase method. The ZnO nanocrystals were synthesized using the wet chemical route and the effect of temperature variation on the structural properties of investigated synthesized using powder x-ray diffractogram (XRD). The temperatures for the synthesis were varied from 120 °C to 200 °C in steps of 20 °C. The results show that, during the first stage of the synthesis of ZnO (at 120 °C), the XRD diffraction pattern confirms the cubic structure of zinc peroxide and the XRD pattern of the samples obtained at temperatures of 140 °C, 160 °C, 180 °C and 200 °C were confirmed to be hexagonal (wurtzite) crystal structure of ZnO. The XRD diffraction patterns of the 140 °C and 160 °C samples show some impurity phases which were associated with the zinc acetate by-product which is a colloid complex of water and methyl succinate and were removed by evaporation as temperatures were increased to 180 °C and 200 °C respectively. As temperature increases, the peak of the diffractograms of the sample becomes sharper and narrow indicating a decrease in width. A shift in peak positions to higher angles was observed and the positional parameter, bond angle, β, average crystallite size, APF, number of unit cells and density generally increase with temperature. However, the lattice parameters ‘a’ and ‘c’, bond lengths b and b1, bond angle, α, dislocation density, strain and unit cell volume were found to generally decrease with temperature.

12 January 2019 in Advanced Nano Research
Verified
Journal Article
Open access
PDF file
EAEsau Abekah Armah
Esau Abekah Armah
FAFrancis Kofi Ampong
Francis Kofi Ampong
MEMartin Egblewogbe
Martin Egblewogbe
HKHubert Azoda Koffi
Hubert Azoda Koffi
FBFrancis Boakye
Francis Boakye
RNRobert Kwame Nkum
Robert Kwame Nkum
There is a substantial amount of literature dealing with many aspects of synthesis and characterization of pure and doped binary compounds including Mn-doped ZnO which has been widely studied due to its superb properties as a dilute magnetic semiconductor (DMS).Aspects concerning doping limits for these compounds is an important stage in the search for new materials. Samples of Zn1-xMnxO nanocrystal were synthesized at temperatures of 180 °C and 200 °C using wet or liquid phase synthesis method. Dopant concentrations x=0.5, 1, 1.5, 2, 2.5, 5, 10, 20, 30, 40 and 50 per cent were studied. Powder x-ray diffraction (PXRD) patterns of the samples were analyzed with a view to determining the onset of secondary phases and hence the solubility limit of the dopant. The solubility limit for Mn in ZnO samples synthesized at temperature of 200 °C is realized at x <20%. For samples synthesized at temperature of 180 °C, the solubility limit is x <0.5%.

5 March 2020 in Journal of Modern Materials
Verified
Journal Article
Open access
PDF file
EAEsau Abekah Armah
Esau Abekah Armah
HKHubert Azoda Koffi
Hubert Azoda Koffi
JAJosef K Ametefe Amuzu
Josef K Ametefe Amuzu
This study explore the possibility of using waste ground palm kernel (GPK) shells as partial replacement of cement in concrete using mechanical destructive method has been studied. The palm kernel shells were in two forms: the GPK ordinary shells and shells subjected to incomplete combustion (i.e. the GPK “fuel” shells). In the preparation of the concrete specimens the mix ratio was 1: 2: 4 (cement: sand: stone) by weight and the replacement percentage was 0%, 20%, 30%, 40%, 50% and 60% respectively. Concrete specimen were molded in both cubic and cylindrical form and its impact on the mechanical properties such as workability, compressive strength and flexural strength using destructive test method were studied. The cubic specimen were tested at 7, 28 and 60 days whiles the cylindrical specimen were tested at 7 and 28 days. Results of physical and chemical analyses suggest that GPK “fuel” shells have acceptable cementitious properties whiles GPK ordinary shells does not. Generally, the compressive and flexural strengths of concrete containing GPK shells decrease as the replacement percentage increases. However, the values of these properties increase as the period of curing increases. The optimum level of GPK shells replacement is 20% for the ordinary shells and 30% for the “fuel” shells considering compressive strength at 28 days for the cubic samples. For the flexural strength on the cylindrical specimen, up to 60% replacement of cement by GPK shells cured for 28 days has acceptable flexural strength. In spite of the findings that the GPK ordinary shells do not have cementitious properties, the mechanical properties on such concretes can be used in low strength constructions as pavements, walk ways and non structural domestic work at a lower cost than using cement.

13 July 2019 in Journal of Modern Materials
Verified
Journal Article
Open access
PDF file
EAEsau Abekah Armah
Esau Abekah Armah
HKHubert Azoda Koffi
Hubert Azoda Koffi
BSBright J. A. Y Sogbey
Bright J. A. Y Sogbey
JAJosef K. Ametefe Amuzu
Josef K. Ametefe Amuzu
The objective of this research is to investigate the utilization of palm kernel shells in ground form (GPK) for partial replacement of ordinary Portland cement (OPC) in concrete by investigating its optimal strength using nondestructive ultrasonic pulse velocity method for both cubic and cylindrical concrete test specimen. In all a total of 135 cubes and 66 cylinders of concrete were prepared. The dimension of the cubic concrete specimens was 150 × 150 × 150 mm and that of the cylindrical specimens were 110 mm and 500 mm diameter and length respectively. The mix design of the GPK shells used as a partial replacement for OPC ranged between 0% and 50% by weight of cement using mix ratio of 1:2:4 with water to cement ratio of 0.8. The concrete specimens were test at curing periods of 7 days, 28 days and 60 days for the cubes and 7 days and 28 days for the cylinders. Based on the results and the analysis done, it was generally observed in all cases that, as the mix ratio is increased, the ultrasonic pulse velocity, modulus of elasticity and the density decreased and as the curing period increased, these values increased across all the mix ratios. The ultrasonic pulse velocity and the density of the specimens shows that concretes containing GPK “fuel” shells has higher values than those containing GPK ordinary shells. Generally, the density, ultrasonic pulse velocity and the modulus of elasticity of concrete containing GPK shells decrease as the replacement percentage increase.