1 April 2019 in Nature Communications
Formaldehyde is an important intermediate product in the catalytic conversion of methanol to olefins (MTO). Here we show that formaldehyde is present during MTO with an average concentration of ~0.2 C% across the ZSM-5 catalyst bed up to a MeOH conversion of 70%. It condenses with acetic acid or methyl acetate, the carbonylation product of MeOH and DME, into unsaturated carboxylate or carboxylic acid, which decarboxylates into the first olefin. By tracing its reaction pathways of 13C-labeled formaldehyde, it is shown that formaldehyde reacts with alkenes via Prins reaction into dienes and finally to aromatics. Because its rate is one order of magnitude higher than that of hydrogen transfer between alkenes on ZSM-5, the Prins reaction is concluded to be the major reaction route from formaldehyde to produce dienes and aromatics. In consequence, formaldehyde increases the yield of ethene by enhancing the contribution of aromatic cycle.
4 March 2020 in ACS Catalysis
SKSebastian L. Kollmannsberger
Sebastian L. Kollmannsberger
22 December 2021 in ACS Energy Letters
Oxide-supported single-atom catalysts are commonly modeled as a metal atom substituting surface cation sites in a low-index surface. Adatoms with dangling bonds will inevitably coordinate molecules from the gas phase, and adsorbates such as water can affect both stability and catalytic activity. Herein, we use scanning tunneling microscopy (STM), noncontact atomic force microscopy (ncAFM), and X-ray photoelectron spectroscopy (XPS) to show that high densities of single Rh adatoms are stabilized on α-Fe2O3(11̅02) in the presence of 2 × 10–8 mbar of water at room temperature, in marked contrast to the rapid sintering observed under UHV conditions. Annealing to 50 °C in UHV desorbs all water from the substrate leaving only the OH groups coordinated to Rh, and high-resolution ncAFM images provide a direct view into the internal structure. We provide direct evidence of the importance of OH ligands in the stability of single atoms and argue that their presence should be assumed when modeling single-atom catalysis systems.
7 August 2019 in Angewandte Chemie International Edition
According to textbooks, tertiary alcohols are inert towards oxidation. The photocatalysis of tertiary alcohols under highly defined vacuum conditions on a titania single crystal reveals unexpected and new reactions, which can be described as disproportionation into an alkane and the respective ketone. In contrast to primary and secondary alcohols, in tertiary alcohols the absence of an α‐H leads to a C−C‐bond cleavage instead of the common abstraction of hydrogen. Surprisingly, bonds to methyl groups are not cleaved when the alcohol exhibits longer alkyl chains in the α‐position to the hydroxyl group. The presence of platinum loadings not only increases the reaction rate but also opens up a new reaction channel: the formation of molecular hydrogen and a long‐chain alkane resulting from recombination of two alkyl moieties. This work demonstrates that new synthetic routes may become possible by introducing photocatalytic reaction steps in which the co‐catalysts may also play a decisive role.
25 June 2020 in ACS Catalysis
SKSebastian L. Kollmannsberger
Sebastian L. Kollmannsberger
4 February 2021 in Advanced Materials Interfaces
Iron oxides (FeOx) are among the most common support materials utilized in single atom catalysis. The support is nominally Fe2O3, but strongly reductive treatments are usually applied to activate the as‐synthesized catalyst prior to use. Here, Rh adsorption and incorporation on the () surface of hematite (α‐Fe2O3) are studied, which switches from a stoichiometric (1 × 1) termination to a reduced (2 × 1) reconstruction in reducing conditions. Rh atoms form clusters at room temperature on both surface terminations, but Rh atoms incorporate into the support lattice as isolated atoms upon annealing above 400 °C. Under mildly oxidizing conditions, the incorporation process is so strongly favored that even large Rh clusters containing hundreds of atoms dissolve into the surface. Based on a combination of low‐energy ion scattering (LEIS), X‐ray photoelectron spectroscopy (XPS) and scanning tunneling microscopy (STM) data, as well as density functional theory (DFT), it is concluded that the Rh atoms are stabilized in the immediate subsurface, rather than the surface layer.