Alexia Chabot

Alexia Chabot

Auto-generated profile, based on publicly available information

Alexia Chabot

MAT, Université Libre de Bruxelles, Brussels, Belgium

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 October 2019 in Journal of Intelligent Manufacturing
Verified
Journal Article
Closed access
PDF file
ACA. Chabot
A. Chabot
NLN. Laroche
N. Laroche
ECE. Carcreff
E. Carcreff
MRM. Rauch
M. Rauch
JHJ.-Y. Hascoët
J.-Y. Hascoët

13 February 2019 in Welding in the World
Verified
Journal Article
Closed access
PDF file
ACA. Chabot
A. Chabot
MRMatthieu Rauch
Matthieu Rauch
JHJ.-Y. Hascoët
J.-Y. Hascoët

20 July 2021 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
ACAlexia Chabot
Alexia Chabot
MRMatthieu Rauch
Matthieu Rauch
Jean-Yves HascoetJean-Yves Hascoet
Jean-Yves Hascoet

26 July 2025 in Journal of Materials Science: Materials in Engineering
Verified
Journal Article
Open access
PDF file
ACAlexia Chabot
Alexia Chabot
TMThibaut Motteu
Thibaut Motteu
JCJérémy Chevalier
Jérémy Chevalier
SGStéphane Godet
Stéphane Godet
Due to current challenges related to global warming and the ecological impact of materials, the industry is considering natural-fibre-reinforced thermoplastic composites for their low weight and sustainability. However, to be considered for structural applications, their mechanical behaviour and damage mechanisms need to be fully understood. Regarding Flax-Polypropylene (Flax-PP) composites, damage mechanisms are successfully identified in the literature; however, their initiation and propagation up to final failure are not well described yet. The present study focuses on a spread-tow woven Flax-PP composite and aims to investigate the damage mechanisms and their evolution in two configurations — namely with fibres of the top ply being either parallel or perpendicular to the loading direction. The damage mechanisms are first identified via SEM analysis of fracture surfaces after standard tensile testing. Then, for both configurations, the evolution of damage mechanisms is studied by in situ SEM micro-tensile testing. In both cases, crack initiation at fibre tips and fibre debonding is the primary failure mechanisms, leading to subsequent fibre pullout and preferred crack path. Results show that the crack path is more in the case of top ply fibres parallel to the loading direction than in the case of transversal fibres. The greater occurrence of fibre pullout compared to fibre breakage is attributed to the weak interfacial strength between the fibres and the matrix, which is typical for natural fibre composites. The present study used in situ investigation to propose a detailed sequence of damage evolution related to tensile loading.

4 August 2026 in Polymer Degradation and Stability
Verified
Journal Article
Closed access
YZYifan Zhu
Yifan Zhu
JMJessica Mangialetto
Jessica Mangialetto
ACAhmad Shawki Charkieh
Ahmad Shawki Charkieh
ACAlexia Chabot
Alexia Chabot
GHGuillermo Meza Hernandez
Guillermo Meza Hernandez
LPLincy Pyl
Lincy Pyl

4 April 2026
Verified
Thesis
Closed access
ACAlexia Chabot
Alexia Chabot
La Fabrication Additive métallique apporte de nouvelles possibilités de fabrication et de liberté de conception des pièces fonctionnelles métalliques par rapport aux procédés conventionnels. En particulier, les technologies Direct Energy Deposition (DED), notamment les procédés Laser Metal Deposition (LMD) et Wire-Arc Additive Manufacturing (WAAM) fusionnent directement la matière et la déposent couche par couche pour réaliser une pièce. Actuellement, ces procédés sont majoritairement mis en œuvre en boucle ouverte. Ainsi, l’obtention d’une pièce conforme aux exigences du cahier des charges résulte le plus souvent d’une méthode essai-erreur. Afin d’améliorer la maitrise des procédés DED et de s’affranchir de cette méthode essai-erreur, la simulation numérique et le monitoring sont les principales pistes investiguées dans la littérature. Cette thèse propose une méthodologie générique de monitoring multiphysique, basée sur quatre boucles de contrôle indépendantes et pouvant être mises en œuvre simultanément. Ces boucles de contrôle se focalisent sur la température, la géométrie et la santé matière de la pièce, ainsi que sur le Stick Out. Dans ces travaux, les boucles de contrôle ont été principalement implémentées sur le procédé WAAM. Un soin particulier a été porté sur leur développement pour rendre ces boucles de contrôle adaptables au procédé LMD. Parallèlement à ces travaux, certains outils numériques existants ont été évalués dans l’optique d’être intégrés dans l’environnement de fabrication aux côtés du monitoring. Cette thèse s’inscrit dans le cadre du laboratoire commun Joint Laboratory of Marine Technology regroupant Naval Group et Centrale Nantes