During underground coal gasification (UCG), whereby coal is converted to syngas in situ, a cavity is formed in the coal seam. The cavity growth rate (CGR) or the moving rate of the gasification face is affected by controllable (operation pressure, gasification time, geometry of UCG panel) and uncontrollable (coal seam properties) factors. The CGR is usually predicted by mathematical models and laboratory experiments, which are time consuming, cumbersome and expensive. In this paper, a new simple model for CGR is developed using non-linear regression analysis, based on data from 11 UCG field trials. The empirical model compares satisfactorily with Perkins model and can reliably predict CGR.
27 May 2018 in Mitigation and Adaptation Strategies for Global Change
Determining a suitable distance between two adjacent panels’ working faces (DBTF) is an important issue that should be considered in underground mining methods. A suitable DBTF causes a decrease in stresses on the pillar, reduces the width of the pillar, and controls the ground subsidence. The main purpose of this study was to determine the suitable DBTF in shortwall mining of the Tabas central coal mine. For this purpose, at the beginning, an algorithm is presented for numerical modeling. In this algorithm, front abutment stresses first and then side abutment stresses are evaluated on the chain pillar. Numerical modeling is performed by finite-difference method software in different distances of P5 and P6 panels’ working faces (5–45 m). The result of this research shows that the front abutment stress on the chain pillars is not different for a distance of 25 m or more. Moreover, by increasing the distance up to 25 m, the side abutment stress in the vicinity of the P5 panel face is decreased on th...
19 December 2019 in International Journal of Coal Science & Technology
The determination of operational parameters in the underground coal gasification (UCG) process should be considered in two aspects: first, the total coal in each UCG panel must be gasified and second, the calorific value of the produced gas should be acceptable. The main aim of this study is to present a model that meets these aspects and increasing the calorific value of syngas during this process. In order to achieve those aims, eight different increasing scenarios were devised for total gasification of coal per panel. These scenarios included: increasing oxygen injection rate (scenario 1), the amount of steam injection (scenario 2), operation time (scenario 3), cavity pressure (scenario 4), increase operation time and cavity pressure simultaneously (scenario 5), increase steam injection speed and oxygen injection rate simultaneously (scenario 6), increase in cavity pressure, operating time, steam injection rate and oxygen injection rate simultaneously (scenario 7) and also simultaneous increase in the operating time and steam injection rate (scenario 8). The results showed that for producing syngas with a higher calorific value, the following parameters had the most positive effects respectively: operation time, cavity pressure, steam injection rate and oxygen injection rate. Finally, the model validation was performed for the Centralia LBK-1 UCG pilot and the results showed that this model is very close to reality.
1 January 2024 in International Journal of Energy Research
The release of methane into the working area of coal mines can affect safety and production. Therefore, methane drainage reduces the risk of explosion and can be used as a fuel and energy source. One methane drainage method is cross‐measure borehole drilling, which involves drilling boreholes from tailgate roadways to the roof or floor layers of a mined seam. In this method, determining the appropriate distance between methane drainage stations has a significant impact on increasing the efficiency of operation and reducing drilling costs and the time required for drainage operations from each station. In this paper, a new 3D numerical model is developed for methane drainage from an underground coal mine to determine the suitable distance between methane drainage stations in the cross‐measure borehole method using COMSOL Multiphysics software. For this purpose, by considering the porous media flow module and the laws related to the movement of gas in the goaf, different numerical models for distances of 10, 15, 20, 25, and 30 m were simulated. The simulation results showed that by reducing the distance between methane drainage stations, the speed of gas flow in the borehole and the amount of gas removed from the boreholes in a similar period of time increase to an acceptable level. In addition, the implementation of this model in a case study showed that a distance of 10 m between drainage stations increases the efficiency of boreholes to approximately 20%. Numerical simulation in this study can provide basic support for the design of drainage boreholes and reduce the risk of gas in underground coal mines.