Seung H. Han

Seung H. Han

Auto-generated profile, based on publicly available information

Seung H. Han

FlexPower Company Ltd., Hwaseong, South Korea

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 November 2019 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
JKJi H. Kim
Ji H. Kim
BCByeongguk Choi
Byeongguk Choi
SJSeogyong Jeong
Seogyong Jeong
SHSeung H. Han
Seung H. Han
HKHoi R. Kim
Hoi R. Kim
Yun-Su KimYun-Su Kim
Yun-Su Kim
In this paper, a novel structure of a receiving (Rx) coil with only two coils, which enables omnidirectional wireless power transfer (WPT) for any type of transmitting (Tx) system, is proposed for the first time. The coil adopts each coils into plane cross-shaped ferrite core, with each leg of the ferrite core intersecting both coils. The intersecting direction of the ferrite core for one coil is identical to that of the other one when it is rotated 90 degrees. It is verified that voltage will be induced on at least one coil with any direction of magnetic flux. With an analysis of circuit diagram, it is shown that a high quality factor of each coil can guarantee an omnidirectional power transfer even when the coupling coefficient between two coils has a non-zero value. A simulation model and an experimental prototype is built to verify the omnidirectional WPT of the proposed Rx coil structure, with loop-type Tx coil as an example among various Tx types. Omnidirectional power transfer capability of the proposed coil was verified with a LED load. The superiority of the proposed coil was verified by comparison with other Rx coil structures also.

21 May 2018 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
BCByeongguk Choi
Byeongguk Choi
YSYeong-Hoon Sohn
Yeong-Hoon Sohn
Eun S. LeeEun S. Lee
Eun S. Lee
SHSeung H. Han
Seung H. Han
HKHoi R. Kim
Hoi R. Kim
CRChun T. Rim
Chun T. Rim
New coreless transmitting (Tx) coils with a conductive material plate for wide-range ubiquitous inductive power transfer (IPT) zones, i.e., a U-IPT zones, where electric devices can be wirelessly charged during operation, are proposed in this paper. Because commercialized IPT systems are only available for short distances of several centimeters and one-to-one charging, the demand is increasing for U-IPT zones in which long-distance wireless charging with 3-D free-positioning and simultaneous charging of multiple receiving (Rx) coils can be achieved. To satisfy this demand, U-IPT zones should be constructed to have a uniform magnetic field distribution in a wide space, which also poses no risk to the human body. In addition, to generate a uniform magnetic field in a wide 3-D space, such as a single room, the system requires the installation of many Tx coils above the ceilings and behind the walls of the room, and these coils should be capable of high electrical performance to support the efficiency of the entire IPT system and should be of excellent mechanical quality. Therefore, a U-IPT zone should meet the following four criteria: human safety, free-positioning of Rx coils, magnetic field uniformity, and economization. By virtue of a conductive material plate that cancels out the undesired direction of magnetic flux generated from the return wires, the proposed coreless Tx coil does not need any heavy ferromagnetic cores, which can cause non-uniformity of the magnetic field distribution and difficult construction. A prototype coreless Tx coil with the dimensions of 1 m × 1 m × 10 cm was fabricated and experimentally verified for a 1 m × 1 m U-IPT zone. The experimental results showed that 74%, 83%, and 76% high magnetic field uniformity could be achieved for $z1$ = 25 cm, 50 cm, and 75 cm, respectively, and 3-D omnidirectional wireless power delivery was achieved, while the guideline of the International Commission on Non-Ionizing Radiation Protection (ICNIRP) for human safety was satisfied throughout the entire U-IPT zone. Moreover, the weight of the entire system was only 9 kg, enabling easy installation. In the multiple wireless charging experiments, 47 W of power was consumed in total by load resistors, each of them connected to nine Rx coils, respectively, with 32 % power efficiency at $z1$ = 20 cm.

27 September 2021 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
Eun S. LeeEun S. Lee
Eun S. Lee
MKMyung-Yong Kim
Myung-Yong Kim
SKShin M. Kang
Shin M. Kang
SHSeung H. Han
Seung H. Han
Inductive power transfer (IPT) systems based on segmented transmitter (Tx) coils are newly proposed in this article. These IPT systems can deliver wireless power to multiple transport robots in an electrified monorail system (EMS) for continuous transportation missions. Considering the one-dimensional long-line driving characteristics of the transport robots having receiver (Rx) systems, a segmented Tx coil structure is introduced so that flexible Tx installation, easily Tx coil fabrication, and insensitive IPT characteristics are possible. In this case, in order to remove the magnetic dead-zones at the adjacent sections between the adjacent Tx coils, folded Tx coils, and an optimally sized Rx coil are applied to the proposed IPT system in this article. Thus, continuous wireless powering to multiple transport robots in the EMS and flexible extending of the Tx length are possible by the proposed IPT systems. For the soft-switching operations of the proposed IPT systems, a gyrator-based static circuit modeling is presented in order to select an appropriate resonant capacitance. By the proposed gyrator-based circuit analysis, it is found that high efficiency Tx circuit operation can be achieved, regardless of the number of Rx and the load conditions. The proposed segmented multiple Tx systems and the 30 W Rx systems for the transport robots were fabricated and verified by experiments for various operating scenarios. Compared with the conventional 2-m-long Tx coil having 69.1% dc power efficiency, the two-segmented 1-m-long Tx coil systems have no powering dead zone and achieved 74.2% dc power efficiency for one 30 W Rx system. As a result, the proposed two segmented 1-m-long Tx systems have 5.1% higher dc efficiency than the conventional 2-m-long Tx coil under the 2-m-long driving route in EMS application.

17 November 2021 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Verified
Journal Article
Closed access
Eun S. LeeEun S. Lee
Eun S. Lee
SHSeung H. Han
Seung H. Han
As the automated guided vehicles (AGVs) play an important role in automated logistics systems, the wireless power transfer (WPT) technologies become a viable solution to provide the AGV with the automatic power charging service. In order to install the WPT systems to the small confined space in the AGV, a 2-D thin coil design is necessary for the receiver (Rx) system installed in the AGV. To greatly reduce the thickness of the Rx coil, including resonant capacitors, an ac/dc rectifier, and dc-link capacitors, an 2-D coil design for a minimum core loss is newly proposed in this article. Based on a finite-element-method (FEM) 3-D simulation analysis, various coil structures have been comparatively evaluated to find the most appropriate core structure. Furthermore, to obtain the highest coil efficiency at nominal operating condition, the appropriate number of turns design is established. Thus, according to the coil design guideline of the proposed inductive power transfer (IPT) system, the appropriate number of turns for transmitter (Tx) and Rx coils $N_{\mathrm {1,op}}$ and $N_{\mathrm {2,op}}$ can be appropriately selected for the high efficient operation of the IPT coils. The 2.5-kW prototypes of the IPT systems for wireless charging of AGV were fabricated and verified by simulations and experiments. The results showed that the total thickness of the coil sets including all the components is 32.0 mm for the Rx coil. The measured maximum coil efficiency for $P_{L} =2.5$ kW at 40-mm coil distance was 98.9% by the proposed IPT coil design procedure. The measured temperatures at the ferrite core and coil for the Rx coil were managed below 53.3 °C and 59.3 °C during 2.5-kW wireless charging, respectively, under a 10-min charging and 20-min AGV operation cycle, which provides the thermal-stable operation of the proposed IPT systems.

30 August 2021 in IEEE Access
Verified
Journal Article
Open access
Eun S. LeeEun S. Lee
Eun S. Lee
JPJin H. Park
Jin H. Park
MKMyung-Yong Kim
Myung-Yong Kim
SHSeung H. Han
Seung H. Han
In this paper, an integrated transformer design methodology for dual-active-bridge (DAB) converters, which basically utilize leakage inductance so as to substitute a cumbersome inductor in the conventional DAB converters, is newly proposed. The proposed integrated transformer with integrated leakage inductance inherently includes leakage inductance and magnetizing inductance, whose values can be appropriately selected by modulating the number of turns and the center-core air-gap. Based on the theoretical analysis of the DAB converters, the major parameters, i.e., primary and secondary current levels and its phase difference, can be derived, and these values are utilized for magnetic analysis of the proposed integrated transformer. Considering core loss and copper loss of the proposed integrated transformer in the DAB converters, optimal values of the center-core air-gap $l_{g}$ and the optimal number of turns $N_{\mathrm {1,}op} ~\&~ N_{\mathrm {2,}op}$ can be determined so that high power efficiency is achieved at a normal operating point of the DAB converters. The 20W prototypes of the DAB converter with EER2834 and EER3019 of the ferrite cores were fabricated and verified by simulation and experiment. The design results showed that the optimal number of turns at $l_{g} =2.0$ mm are found to be 11 and 10, for the EER2834 and EER3019, respectively. Compared to 94.5% and 96.3% of AC efficiencies for the conventional transformer and inductor set, the proposed integrated transformer achieved 95.8% and 96.9% of AC efficiencies at maximum power transfer point of $\theta _{p} = \pi $ /2 for EER2834 and EER3019, respectively.

25 January 2021 in IEEE Access
Verified
Journal Article
Open access
Eun S. LeeEun S. Lee
Eun S. Lee
BCByeongguk Choi
Byeongguk Choi
MKMyung-Yong Kim
Myung-Yong Kim
SHSeung H. Han
Seung H. Han
The coil design of the inductive power transfer (IPT) for a transmitter (Tx) and receiver (Rx) is crucial to determine the performance of the IPT. Considering core loss and copper loss of the Tx and Rx coils, which are major loss terms of the whole IPT system, determination of the winding turns for the Tx and Rx coils becomes a key factor for maximum power transfer design of the IPT coils. In this paper, an optimal turns design of IPT coils for laptop wireless charging applications with a maximum power transfer efficiency is proposed. Under a specific design requirement of IPT, optimal turns of the Tx and Rx coils N1,op and N2,op can be determined by the proposed IPT coil design procedure with a finite-element-method (FEM) based simulation analysis. From the results of the coil design by the proposed IPT coil design methodology, N1,op and N2,op for maximum power efficiency, and input DC voltage V dc for the target load power can be found by the proposed coil design procedure. The 40W prototypes of the two symmetry and asymmetry IPT coils for laptop wireless charging were fabricated, and verified by simulation and experiments. To separately verify the core and copper loss of the IPT coils, a resistance model and Steinmetz equation-based methods were comparatively evaluated, and it was found that they matched well at a core temperature condition of below 40oC. The results showed that the total weight and the thickness of the Tx and Rx coils as well as the maximum power efficiencies of 95.1% and 96.8% for the symmetry and asymmetry cases were obtained by the proposed IPT coil design procedure, which becomes a practical solution for the laptop wireless charging coil design.