Peng Wang

Peng Wang

Auto-generated profile, based on publicly available information

Peng Wang

School of Electrical Engineering, Southeast University, Nanjing, China

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 June 2021 in IEEE Transactions on Energy Conversion
Verified
Journal Article
Closed access
KLKeman Lin
Keman Lin
PWPeng Wang
Peng Wang
PCPeizhao Cai
Peizhao Cai
XWXikun Wu
Xikun Wu
Mingyao LinMingyao Lin
Mingyao Lin
The square-wave voltage signal injection method with the proportional-integral (PI) observer is commonly adopted to estimate the rotor position of interior permanent magnet synchronous motor (IPMSM). However, the saliency estimation method with PI observer is a continuous injection method and the polarity identification method is a discrete one, which causes extra transition time and complexity. To solve this problem, a fast unipolar sequence-pulse injection method is proposed to unify the process of saliency and polarity identification and the complexity of the algorithm as well as the identification time are reduced. At the same time, a four-stage search algorithm is proposed to ensure the fast convergence and improve the accuracy by reducing the number of the pulse voltage signals. The experiment on motor drive platform verifies the effectiveness of the proposed method to IPMSMs with different saliency ratios.

8 February 2021 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Verified
Journal Article
Closed access
PWPeng Wang
Peng Wang
KLKeman Lin
Keman Lin
XZXu Zhang
Xu Zhang
SWShuai Wang
Shuai Wang
JAJian Ai
Jian Ai
Mingyao LinMingyao Lin
Mingyao Lin
It is essential to estimate stator inductance and rotor flux linkage online for fault diagnosis and high-performance control of surface-mounted permanent magnet synchronous machine (SPMSM). The current injection method is a popular way to estimate the two parameters. However, the dead-time influence of voltage-source-inverter (VSI) and the stator inductance variation caused by injected current could not guarantee the converge of the estimation. To solve the above two problems, a method of injecting square-wave angle for online parameter estimation is proposed in this article. First, the theory of eliminating dead-time influence with and without square-wave angle injection is analyzed. Next, the least square algorithm is adopted to estimate stator inductance without injection. Then, the rotor flux linkage is estimated by injecting a square-wave angle. The saturation effect of estimation is also analyzed, and both parameters are estimated without acquiring any nominal values. At last, the appropriate amplitude and frequency of square-wave angle are determined by the parameter error and convergence analysis. The proposed method is evaluated with simulation and extensive experiments under various speed and load conditions. It is noteworthy that not less than two parameters are estimated without the dead-time influence and the injection will not cause inductance variation, which is different from the previous work.

22 January 2021 in IET Electric Power Applications
Verified
Journal Article
Open access
PDF file
PWPeng Wang
Peng Wang
KLKeman Lin
Keman Lin
Mingyao LinMingyao Lin
Mingyao Lin
AYAnchen Yang
Anchen Yang
FFFangyuan Fu
Fangyuan Fu
JAJian Ai
Jian Ai
Online estimation of the machine parameters is essential to fault diagnosis and high‐performance control of permanent magnet synchronous machine (PMSM). The signal injection is an effective way to estimate machine parameters. However, the inductance variation caused by signal injection will result in difficulties for the estimated parameters to converge. At the same time, online parameters estimation brings heavy burden to the operation of control system. To solve these two problems, optimized inductance model is built with the step‐pulse injection to improve the accuracy of estimation. Compared with the existing method, the step‐by‐step parameter estimation method is adopted and orders of feedback matrix are reduced, which improves the computation efficiency. The forgetting factor recursive least square (FFRLS) algorithm is adopted to estimate stator resistance, rotor flux linkage and d ‐, q ‐axes inductances without acquiring any nominal parameter. The minimum amplitude and appropriate frequency of step‐pulse are determined by the parameter error and convergence analysis. The effectiveness of the proposed method is verified via a 1.5 kW PMSM drive platform.