16 July 2019 in IEEE Transactions on Antennas and Propagation
An arm-implantable rectenna, supported by a compact planar inverted F-antenna (PIFA) and a rectifier, is proposed for wireless data telemetry and power transfer in the Medical Device Radiocommunications Service (401-406 MHz) and Industrial, Scientific and Medical (902.8-928 MHz) bands. The rectifier is integrated into the system by using the antenna’s ground plane delivering, thus, a robust solution for the implanted devices. Each development stage is theoretically analyzed first and then experimentally tested. The antenna size is 16 x 14 x 1.27 mm3. The slit/slot loading techniques applied onto the radiator offer the antenna size reduction and the dual-band operation. PIFA’s resonance stability is shown and its radiation and safety responses are addressed. Further, an arm-attached matching layer is proposed to enhance the wireless power link. Then, an analysis of rectifier circuits is conducted in order to obtain optimum conversion efficiency at low input powers. By following an attentive design process, the final system (rectenna) is built and tested in whole; the measurements verify our approach.
1 June 2015 in IEEE Antennas and Wireless Propagation Letters
A novel implantable planar dipole antenna for operation in the Medical Device Radiocommunications Services band (401-406 MHz) is proposed. A basic skin-implantable antenna model is initially developed, and then a prototype is fabricated. The dipole antenna exhibits an extremely thin profile and a very small aperture size; antenna physical volume is approximately 18.1 mm 3. Effective size reduction is achieved by optimally canceling its inherent high capacitance through L-shaped reactive loading sections within the antenna structure. As demonstrated, the applied design methodology facilitates planar antenna miniaturization with adequate radiation response (gain, radiation pattern shape, and specific absorption rate). A liquid skin medium is employed to experimentally validate the antenna. Measured and simulated results are in good agreement.
9 May 2017 in IEEE Transactions on Antennas and Propagation
A design frame for developing miniature implant- able antennas at medical device radiocommunications band (401–406 MHz) is being sketched by addressing issues of resonance, efficiency, bandwidth (BW), and robustness. To that end, we visit fundamental design concepts of geometry, impedance matching, and quality factor Q and we show that a very small antenna insensitive to environmental variations and of optimum efficiency can be obtained. It is the first time, to our knowledge, that a Q calculation for miniature implanted antennas is conducted. In this paper, we consider a skin-tissue implantation scenario and planar dipoles with extremely thin profile and small aperture size. Notably, antennas’ physical volume does not exceed 25 mm3. Results indicate a strong dependence of resonance frequency on the antenna geometry for fixed physical size. In addition, external impedance matching proves to be inferior to integral matching via metallization in relation with antenna radiation performance (gain, efficiency, and quality of communication link). Finally, the quality factor Q of small fixed-size antennas highlights the influence of the design on the exhibited resonance and sensitivity response (impedance BW, tolerance to detuning, and gain stability). Simulations are accompanied by measurements with very good agreement underlying the importance of our approach.
23 April 2026 in IEEE Open Journal of Antennas and Propagation
This work presents a mixed multilayered cavity-backed slot array antenna for the 27 GHz band, fed by a substrate-integrated groove gap waveguide (SIGGW). The proposed antenna structure is based on a three-layer design, consisting of two dielectric substrates for the feeding network and cavity distribution layer, and a metal layer for a corrugated slot array antenna. In the presented multilevel antenna design, the feeding network and cavity layer are implemented by periodic “Mushroom”-type surfaces, creating electromagnetic band gap properties. This allows for easy assembly of the distinct printed layers without requiring an electrical contact or a bonding layer. Simultaneously, we address the potential issue of energy leakage due to surface roughness or non-flat surfaces. Measurements show good agreement with the simulation results. An impedance bandwidth of 11.7%, ranging from 25.6 to 28.8 GHz, is achieved. The measured normalized radiation patterns are symmetrical, with sidelobe levels below -10 dB at both φ = 0° and φ = 90° planes. Finally, the maximum peak gain is measured at 17.72 dBi, along with a radiation efficiency of 84% and an aperture efficiency of 77% at the central operating frequency.