Reza Ghazi

Reza Ghazi

Auto-generated profile, based on publicly available information

Reza Ghazi

Department of Electrical Engineering, Ferdowsi University of Mashhad, Mashhad, Iran

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 May 2020 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
SHSeyed Hossein Hosseini
Seyed Hossein Hosseini
RGReza Ghazi
Reza Ghazi
HHHamed Heydari-Doostabad
Hamed Heydari-Doostabad

17 March 2021 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
HHHamed Heydari-Doostabad
Hamed Heydari-Doostabad
SHSeyed Hossein Hosseini
Seyed Hossein Hosseini
RGReza Ghazi
Reza Ghazi
Terence O'DonnellTerence O'Donnell
Terence O'Donnell
This article proposes a bidirectional battery charger for grid to vehicle and vehicle to grid operations of electric vehicles (EV). The dc stage of the proposed converter offers a quadratic buck–boost voltage gain ratio, which makes it suitable for interconnecting the battery pack unit of EVs with both dc and ac grids as a home EV charger. A high-voltage gain ratio, low voltage, and current stress of switches, high values of utilization factors (UF) for both directions are achieved. Continuous input current and common electrical ground are preserved at the dc–dc stage and also, the continuous output current of the proposed converter makes the realization of the pseudo dc-link method possible for connecting to an ac grid. Consequently, the switching power loss in the dc–ac stage of the EV charger is reduced, and as a result, it allows the proposed charger to run more efficiently and cooler. The operating principle, steady-state characteristics including the current, voltage stress, and UF of the switches, and comparison with other state-of-the-art dc–dc bidirectional converters are carried out in detail. Finally, to verify the theoretical achievements, a 500-W laboratory prototype of the proposed EV charger is implemented. The EV charger exhibits the capability for ac and dc regulation and demonstrates peak efficiency of 97.8% in the forward and 97.5% in the backward direction modes of operation.

24 August 2021 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
MPMaryam Pourmahdi
Maryam Pourmahdi
HHHamed Heydari-Doostabad
Hamed Heydari-Doostabad
RGReza Ghazi
Reza Ghazi
Terence O'DonnellTerence O'Donnell
Terence O'Donnell
This article proposes new common ground bridgeless power factor correction rectifiers suitable for use in any application which requires a positive or negative dc power supply. The main advantage of the proposed rectifiers, compared to previous works, is the provision of the common ground between input and output, which eliminates electromagnetic interference (EMI) associated with high rates of change of voltage and consequently reduces the need for EMI common mode filtering. The converter also provides step-down and step-up operation, and facilitates positive or negative output voltages with a low number of semiconductor devices operating simultaneously. High power factor, acceptable grid-side current quality, and high efficiency are also achieved. Two variants are presented, referred to as type-I and type-II, which offer common ground positive and negative dc voltages, respectively. Closed-loop control of the converters is provided by a dead-beat current controller in the inner loop. Experimental results are presented for a 500-W prototype, operating from 220 and 110 Vrms input to $\pm$ 48 and $\pm$ 200 Vdc output. The experimental results demonstrate the capability for step-down and step-up ac-to-dc power conversion with a peak efficiency of 96.8% and 96.6% in the positive and the negative outputs, respectively.

24 April 2018 in IET Renewable Power Generation
Verified
Journal Article
Open access
PDF file
MMMajid Mehdizadeh
Majid Mehdizadeh
RGReza Ghazi
Reza Ghazi
MGMohsen Ghayeni
Mohsen Ghayeni
Increasing the wind energy penetration in a power system presents some technical challenges to the transmission expansion planning (TEP). In the first stage of TEP, the transmission bottlenecks should be determined and ranked via security assessment. The high penetration of wind energy means a large number of wind farms exist in various geographic areas. It is found that there is a correlation between the wind speed series of different farms. Therefore, integration of the correlated wind farms into security assessment is addressed in this study. Hence, a new model of wind speed prediction is presented based on the correlated autoregressive moving average time series. The copula functions are used to make the predefined correlation among wind speed series. Here a linear correlation using a Gaussian copula is implemented. Then, the risk‐based security assessment is performed using the proposed sequential time simulation. The proposed process is applied to the modified IEEE 39‐bus test system which comprises 15 wind farms. Then, the transmission bottlenecks are identified and ranked regarding their overload risks. Finally, the impacts of the wind farms correlation on the risk index are investigated and those contingencies which impose the highest influence on this risk are identified.

1 February 2019
Verified
Conference Paper
Closed access
MEMohammad Eydi
Mohammad Eydi
SHSeyed Hossein Hosseini
Seyed Hossein Hosseini
RGReza Ghazi
Reza Ghazi
The fundamental DC-DC boost converter has the drawbacks of low voltage gain ratio followed by discontinuous output current. May the reverse recovery problem rises as a disaster for the output diode along with harming the power switch. Also the stress of voltage is significantly high in respect with the output voltage. Therefore, a new topology of high gain non-isolated DC-DC boost converter is proposed in this paper. In this converter a high voltage gain is achieved with continuous power in the input and the output. The voltage stresses across the semiconductors are all less than that of fundamental boost converter in respect with the output voltage. Only a single power switch is controlled by PWM which leads to simplicity and cost reduction. The proposed converter is advisable for PV panels because of its continuous input current. Furthermore, as the output current is also continuous this makes it a suitable choice for fuel cells. Simulations are provided in MATLAB Simulink to verify the extracted theoretical equations from the proposed converter.

5 March 2020 in IET Generation, Transmission & Distribution
Verified
Journal Article
Open access
PDF file
MKMilad Khani
Milad Khani
RGReza Ghazi
Reza Ghazi
BNBehnam Nazari
Behnam Nazari
Distribution overhead line network faults with the potential threats to public safety are of extreme importance. High‐impedance faults (HIFs) occur on distribution feeders with close proximity to the population. Advanced technology has enabled power distribution utilities to detect a high percentage of HIFs. However, the application of HIF detectors (HIFDs) should meet both operational and economic requirements due to expense and a large number of distribution feeders. Installation of these devices on overhead feeders among several candidate feeders seems to be a challenging issue. Therefore, ranking of feeders is essential for equipping them with HIFDs. This study proposes a practical approach which is an improved fuzzy analytic hierarchy process (AHP), accompanied by a constrained non‐linear optimisation model to extract optimal crisp priorities from fuzzified inputs, considering various criteria with a degree of inconsistency in their real data. This improved integrated model is also able to adequately evaluate both qualitative and subjective parts of the location‐allocation problems. In this study, enhanced particle swarm optimisation (EPSO) is used to deal with the optimisation problem for criteria weight ratio and also finding the individual feeder preference weighting to optimally locate HIFDs in distribution feeders. The proposed model is applied on a real network and then sensitivity analysis is performed in the optimal solution.