4 August 2010 in Langmuir
1 November 2012 in Cement and Concrete Research
19 June 2019 in Reaction Chemistry & Engineering
Thermophysical properties of fluid systems are highly desirable as they are used in many industrial processes both from a chemical engineering point of view and to push forward the development of modeling approaches. To access these data, microfluidic approaches have recently attracted increasing interest as they provide flexible and reliable ways for measurements, leading to fast screening capabilities compared to conventional experimental systems. In this review, we present a general overview of microfluidic methodologies integrating in situ characterization to determine thermodynamic properties of fluid systems. In addition to drastically reducing the time to reach thermodynamic equilibria, one major advantage of microfluidics is to provide optical access to the fluid behavior, even under harsh conditions. Therefore, several in situ characterization techniques can be implemented to get insights into fluid properties. Here, we emphasize approaches developed using high pressure and high temperature microfluidics. Indeed, such conditions are of interest for energy industries and present plenty of challenges. Several recent examples of high pressure microfluidics optical approaches will be detailed, in particular to determine viscosity and density, phase equilibria, mass transfer coefficients and solubility parameters.
3 October 2018 in SPE Reservoir Evaluation & Engineering
Surfactant/polymer (SP) flooding is an enhanced-oil-recovery (EOR) process that can lead to incremental oil recovery through two mechanisms: reducing oil/water interfacial tension (IFT) to decrease residual oil saturation and increasing the viscosity of the displacing fluid to improve overall sweep efficiency. IFT reduction allows better oil recovery by overcoming capillary effects, while the increased viscosity of the displacing fluid allows a more-homogeneous sweep of reservoir oil. Implementing chemical flooding in reservoirs with relatively high temperature and in-situ salinity (>200,000 ppm) is somewhat challenging. This paper describes the extensive laboratory work performed for the light-oil Raudhatain Lower Burgan (RALB) Reservoir (180°F/82°C) in Kuwait. Reservoir fluids were thoroughly characterized to preselect the most-suitable chemicals for the SP process. Reservoir crude oil was analyzed and recombined with gases (C1 through C3) depending on the reported gas/oil ratio (GOR) to reproduce the oil in place (OIP) at original reservoir conditions in terms of pressure, temperature, and oil composition. A shift of the live-oil equivalent alkane carbon number (EACN) was compared with the dead-oil EACN. Numerous surfactants were screened according to three main criteria: solubility in the envisioned injection brine, ultralow oil/water IFT, and chemical adsorption on reservoir rock. Different brine types were considered, and the use of adsorption inhibitors was also investigated. Furthermore, polymer screening involving temperature-resistant polymers was conducted by means of viscosity, long-term-aging, and adsorption tests. Polymer compatibility with the selected surfactants was also evaluated. The selected SP formulation was further evaluated through a series of coreflood experiments that were mainly dependent on chemical adsorption on reservoir rock and incremental oil recovery. An injection strategy was designed as a result of these experiments. Laboratory results obtained thus far are encouraging and provide a systematic methodology to design SP injection in high-temperature, high-salinity, and light-oil reservoirs that are similar to the RALB reservoir. Additional technoeconomic evaluation is in progress in preparation for field-scale deployment of SP injection at RALB Reservoir.
1 March 2020 in Journal of Petroleum Science and Engineering
6 November 2019 in SPE Reservoir Evaluation & Engineering
The objective of aqueous-surfactant formulation design is to achieve ultralow interfacial tension (IFT) with the oil in place at reservoir conditions. Several parameters have to be investigated, and among them, it is well-known that the presence of gas dissolved in crude oil can greatly affect the surfactant/brine/crude-oil-microemulsion phase behavior. Omitting it might degrade the formulation performance. In this work, we present a combined experimental and theoretical investigation of optimal-salinity evolution as a function of live-oil compositions and conditions, varying the pressure independently of the gas/oil ratio (GOR) (i.e., the amount of gas dissolved in crude oil). A specific high-pressure/high-temperature (HP/HT) sapphire cell with a mobile piston is used to separately study the effect on the optimal salinity of the GOR by adding different amounts of n-alkanes methane (C1), ethane (C2), and propane (C3) at the corresponding saturation pressure, and the effect of pressure (up to 500 bar) is studied in a second cell by varying the cell volume (without changing the live-crude-oil composition). Using the HP/HT sapphire cell, we show that GOR variations (tested values up to 135 std m3/m3) induce important modifications of the brine/surfactant/oil-microemulsion phase behavior. In the case of the studied fluids, experimental data indicate that the optimal salinity of the brine/surfactant/oil system decreases linearly when increasing the amount of gas dissolved in the live crude oil. As a consequence of the Salager relation (Salager et al. 1979), the equivalent alkane carbon number (EACN) of the live crude oil varies linearly with the GOR. We demonstrate hereafter that the cell pressure alone (up to 500 bar), for a fixed composition (i.e., fixed GOR), affects neither the formation nor the stability of the Winsor III (WIII) microemulsion. Furthermore, results suggest that the composition of the dissolved representative gas can have an effect on the microemulsion phase behavior. Three models have been evaluated to estimate EACN values for 13 live crude oils and for the two live oils of interest in this study [Crude Oil 1 and n-tetradecane (n-C14)]. We compared predictions with our new experimental data. The Creton and Mougin (2016) model quantitatively predicts the behavior of live oils and agrees with the negligible effect of pressure on microemulsion formation and stability.