Daiki Nakajima

Daiki Nakajima

Auto-generated profile, based on publicly available information

Daiki Nakajima

UACJ Corporation R&D Division

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 June 2015 in Current Nanoscience
Verified
Journal Article
Closed access
TKTatsuya Kikuchi
Tatsuya Kikuchi
DNDaiki Nakajima
Daiki Nakajima
ONOsamu Nishinaga
Osamu Nishinaga
SNShungo Natsui
Shungo Natsui
RSRyosuke O. Suzuki
Ryosuke O. Suzuki
Anodizing of aluminum and its alloys is widely investigated and used for corrosion protection, electronic devices, and micro-/nanostructure fabrication. Anodizing of aluminum in acidic solutions causes formation of porous aluminum oxide films, which consists of numerous hexagonal cells perpendicular to the aluminum substrate, and each cell has nanoscale pores at its center. Recently, highly ordered porous aluminum oxide has been widely investigated for various novel nanoapplications. In this review article, we introduce the fundamentals of anodic oxide films including barrier and porous oxides. Then, we summarize the electrolyte species used so far for porous oxide fabrication and describe the self-ordering conditions during anodizing in these electrolyte solutions. Fabrication of highly ordered porous oxides through the vertical section can be achieved by a two-step anodizing and nanoimprint technique. Various nanoapplications based on the ordered porous oxide are also introduced.

1 September 2014 in Applied Surface Science
Verified
Journal Article
Closed access
TKTatsuya Kikuchi
Tatsuya Kikuchi
DNDaiki Nakajima
Daiki Nakajima
JKJun Kawashima
Jun Kawashima
SNShungo Natsui
Shungo Natsui
RSRyosuke, O. Suzuki
Ryosuke, O. Suzuki

1 May 2018 in Applied Surface Science
Verified
Journal Article
Closed access
DNDaiki Nakajima
Daiki Nakajima
TKTatsuya Kikuchi
Tatsuya Kikuchi
SNShungo Natsui
Shungo Natsui
RSRyosuke O. Suzuki
Ryosuke O. Suzuki

1 November 2017 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
RKRyunosuke Kondo
Ryunosuke Kondo
DNDaiki Nakajima
Daiki Nakajima
TKTatsuya Kikuchi
Tatsuya Kikuchi
SNShungo Natsui
Shungo Natsui
RSRyosuke, O. Suzuki
Ryosuke, O. Suzuki

10 December 2014 in Scientific Reports
Verified
Journal Article
Open access
TKTatsuya Kikuchi
Tatsuya Kikuchi
ONOsamu Nishinaga
Osamu Nishinaga
DNDaiki Nakajima
Daiki Nakajima
JKJun Kawashima
Jun Kawashima
SNShungo Natsui
Shungo Natsui
RSRyosuke, O. Suzuki
Ryosuke, O. Suzuki
Anodic oxide fabricated by anodizing has been widely used for nanostructural engineering, but the nanomorphology is limited to only two oxides: anodic barrier and porous oxides. Therefore, the discovery of an additional anodic oxide with a unique nanofeature would expand the applicability of anodizing. Here we demonstrate the fabrication of a third-generation anodic oxide, specifically, anodic alumina nanofibers, by anodizing in a new electrolyte, pyrophosphoric acid. Ultra-high density single nanometer-scale anodic alumina nanofibers (1010[emsp14]nanofibers/cm2) consisting of an amorphous, pure aluminum oxide were successfully fabricated via pyrophosphoric acid anodizing. The nanomorphologies of the anodic nanofibers can be controlled by the electrochemical conditions. Anodic tungsten oxide nanofibers can also be fabricated by pyrophosphoric acid anodizing. The aluminum surface covered by the anodic alumina nanofibers exhibited ultra-fast superhydrophilic behavior, with a contact angle of less than 1[deg], within 1 second. Such ultra-narrow nanofibers can be used for various nanoapplications including catalysts, wettability control, and electronic devices.

1 December 2014 in Applied Surface Science
Verified
Journal Article
Closed access
DNDaiki Nakajima
Daiki Nakajima
TKTatsuya Kikuchi
Tatsuya Kikuchi
SNShungo Natsui
Shungo Natsui
RSRyosuke, O. Suzuki
Ryosuke, O. Suzuki