16 October 2021 in Energy & Environmental Science
Proton conducting electrochemical cells, especially protonic ceramic fuel cells (PCFCs), are expected to be a breakthrough technology in next-generation energy conversion systems, primarily because of their high proton conductivity and low activation energy below 600 °C. However, the low chemical and physical stability of proton conducting oxides during the sintering process has resulted in a substantially lower electrochemical performance than their predictions, limiting their utilization and application. Here, we present the fabrication of a stoichiometric BaZr0.4Ce0.4Y0.1Yb0.1O3−δ (BZCYYb) electrolyte with an average grain size of ∼10 μm by controlling the chemical potential of the A-site cation, Ba, near the BZCYYb electrolyte surface during the sintering process. A stoichiometric BZCYYb-based PCFC in an anode-supported configuration exhibits 1.90 W cm−2 and 1.01 W cm−2 with an extremely low ohmic resistance of 0.060 ohm cm2 at 650 °C and 0.082 ohm cm2 at 550 °C, respectively, surpassing the values of all previously reported PCFCs without complicated engineering in materials and structures of other cell components.
1 January 2021 in Sensors and Actuators B: Chemical
4 May 2021 in Journal of Materials Chemistry A
Stable operation at elevated temperature has significant importance for the commercialization of solid oxide fuel cells. In particular, interdiffusion at the interface between the cathode and the electrolyte during long-term operation leads to the formation of insulating phases, significantly reducing the cell performance. In this study, a simple wet chemical coating method was employed to fabricate a thin, dense Gd0.2Ce0.8O2−δ (GDC) diffusion barrier layer between the La0.6Sr0.4Co0.2Fe0.8-O3−δ (LSCF) cathode and yttria-stabilized zirconia (YSZ) electrolyte with a gelatin hydrogel-based precursor solution. The fabrication of thin dense film GDC using a simple spin coating method was enabled by the interfacial self-assembly of organic/inorganic composites between the precursor and hydrogel. The anode-supported single cell with a hydrogel-assisted GDC chemical diffusion barrier layer showed improved electrochemical performance due to fast ionic conduction via short and highly percolated diffusion pathways, maintaining the initial performance after the accelerated heat treatment at 900 °C for 100 h by preventing the cation interdiffusion at the interface.
18 May 2018 in Journal of Materials Chemistry A
Nano-structured composite electrodes, from a carefully conducted infiltration process, are one of the most promising electrode structures for intermediate temperature solid oxide fuel cells (IT-SOFCs), due to their ability to promote the oxygen reduction reaction (ORR) and enlarge triple phase boundaries (TPBs). Here, we demonstrate rational design of infiltrated nano-structures for IT-SOFCs with enhanced ORR kinetics and excellent stability. We systematically designed a nano-structured cathode functional layer (CFL) from the infiltration of Sm0.5Sr0.5CoO3−δ (SSC) into porous Gd0.2Ce0.8O2−δ (GDC). By controlling the drying process during the infiltration process, two distinct nano-structures of SSC, discrete coating and film-like coating, were fabricated on the GDC scaffolds. The CFL with the film-like coating showed ∼30% reduction in polarization resistance (Rp) and ∼15% increase in peak power density at 650 °C compared to the CFL with the discrete coating in spite of ∼12-fold lower loading of infiltration materials. Furthermore, the CFL with the film-like coating showed an excellent stability, maintaining an Rp of 0.029 Ω cm2 for 100 h at 650 °C. Our results demonstrated that the high performance and stability of composite electrodes for IT-SOFCs can be achieved through a thin-film coated CFL.
2 August 2019 in Journal of Materials Chemistry A
For high-performance intermediate-temperature solid oxide fuel cells (IT-SOFCs), rational design of the interface between the electrode and electrolyte is essential, because interfacial reactivity often dominates the overall performance. In this study, a unique nanowrinkled structure of a Gd0.1Ce0.9O1.95 functional layer is fabricated by electrostatic spray deposition (ESD) between a porous nanostructured electrode and dense electrolyte, for extended and activated reaction sites at the interfaces. Upon the introduction of the nanowrinkled functional layer, the polarization resistance is reduced 3.3-fold, while the peak power density is increased 2.2-fold (0.034 Ω cm2 and 1.19 W cm−2, respectively) at 650 °C, compared to those of the reference sample. The substantial increases in surface area and grain boundary density in the nanowrinkled functional layer reduce both polarization resistance and activation energy, providing a significant performance enhancement. Our results demonstrate the importance of interface engineering with a cost-effective and simple ESD process to fully utilize the nanostructured electrodes for high-performance IT-SOFCs.
6 May 2019 in ACS Applied Energy Materials