11 July 2012 in Journal of Fluid Mechanics
The wake characteristics of bluff-body-stabilized flames are a strong function of the density ratio across the flame and the relative offset between the flame and shear layer. This paper describes systematic experimental measurements and stability calculations of the dependence of the flow field characteristics and flame sheet dynamics upon flame density ratio, ${\rho }_{u} / {\rho }_{b} $ , over the Reynolds number range of 1000–3300. We show that two fundamentally different flame/flow behaviours are observed at high and low ${\rho }_{u} / {\rho }_{b} $ values: a stable, noise-driven fixed point and limit-cycle oscillations, respectively. These results are interpreted as a transition from convective to global instability and are captured well by stability calculations that used the measured velocity and density profiles as inputs. However, in this high-Reynolds-number flow, the measurements show that no abrupt bifurcation in flow/flame behaviour occurs at a given ${\rho }_{u} / {\rho }_{b} $ value. Rather, the flow field is highly intermittent in a transitional ${\rho }_{u} / {\rho }_{b} $ range, with the relative fraction of the two different flow/flame behaviours monotonically varying with ${\rho }_{u} / {\rho }_{b} $ . This intermittent behaviour is a result of parametric excitation of the global mode growth rate in the vicinity of a supercritical Hopf bifurcation. It is shown that this parametric excitation is due to random fluctuations in relative locations of the flame and shear layer.
8 April 2013 in SAE International Journal of Engines
This work is a technical review of past research and a synthesis of current understanding of post injections for soot reduction in diesel engines. A post injection, which is a short injection after a longer main injection, is an in-cylinder tool to reduce engine-out soot to meet pollutant emissions standards while maintaining efficiency, and potentially to reduce or eliminate exhaust aftertreatment. A sprawling literature on post injections documents the effects of post injections on engine-out soot with variations in many engine operational parameters. Explanations of how post injections lead to engine-out soot reduction vary and are sometimes inconsistent or contradictory, in part because supporting fundamental experimental or modeling data are often not available. In this paper, we review the available data describing the efficacy of post-injections and highlight several candidate in-cylinder mechanisms that may control their efficacy. We first discuss three in-cylinder mechanisms that have been frequently proposed to explain how post injections reduce engine-out soot. Thereafter, to provide a foundation for interpretation of past research, we briefly review basic soot formation and oxidation chemistry, and soot/fluid processes in fuel sprays and engine flows. Next, we provide a comprehensive overview of the literature on the efficacy of post-injections for soot reduction as a function of engine operational parameters including injection duration and dwell, exhaust-gas recirculation, load, boost, speed, swirl, and spray targeting. We conclude by identifying major remaining research questions that need to be addressed to help achieve a design-level understanding of the mechanisms of soot reduction by post injections.
1 July 2012 in Physics of Fluids
This work investigates the response of the vortex breakdown region of a swirling, annular jet to transverse acoustic excitation for both non-reacting and reacting flows. This swirling flow field consists of a central vortex breakdown region, two shear layers, and an annular fluid jet. The vortex breakdown bubble, a region of highly turbulent recirculating flow in the center of the flowfield, is the result of a global instability of the swirling jet. Additionally, the two shear layers originating from the inner and outer edge of the annular nozzle are convectively unstable and rollup due to the Kelvin-Helmholtz instability. Unlike the convectively unstable shear layers that respond in a monotonic manner to acoustic forcing, the recirculation zone exhibits a range of response characteristics, ranging from minimal response to exhibiting abrupt bifurcations at large forcing amplitudes. In this study, the response of the time-average and fluctuating recirculation zone is measured as a function of forcing frequency, amplitude, and symmetry. The time-average flow field is shown to exhibit both monotonically varying and abrupt bifurcation features as acoustic forcing amplitude is increased. The unsteady motion in the recirculation zone is dominated by the low frequency precession of the vortex breakdown bubble. In the unforced flow, the azimuthal m = −2 and m = −1 modes (i.e., disturbances rotating in the same direction as the swirl flow) dominate the velocity disturbance field. These modes correspond to large scale deformation of the jet column and two small-scale precessing vortical structures in the recirculation zone, respectively. The presence of high amplitude acoustic forcing changes the relative amplitude of these two modes, as well as the character of the self-excited motion. For the reacting flow problem, we argue that the direct effect of these recirculation zone fluctuations on the flame response to flow forcing is not significant. Rather, flame wrinkling in response to flow forcing is dominated by shear layer disturbances. Recirculation zone dynamics primarily influence the time-average flame features (such as spreading angle). These influences on the flame response are indirect, as they control the transfer function relating shear layer fluctuations and the resulting flame response.
1 October 2022 in Proceedings of the Combustion Institute
17 February 2011 in Combustion Science and Technology
Transverse acoustic instabilities in premixed, swirl-stabilized flames are an important problem in low NOx combustors. Transverse excitation of swirling flames involves complex interactions between acoustic waves and fluid mechanic instabilities. This paper presents high-speed PIV characterization of the flow field characteristics of a swirling, annular jet under reacting and nonreacting conditions. These data show that the flame response to transverse acoustic excitation is a superposition of acoustic and vortical disturbances that fluctuate in both the longitudinal and transverse direction. In the nozzle near-field region, the disturbance field is a complex superposition of short wavelength and convecting vortical disturbances, as well as longer wavelength transverse and longitudinal acoustic disturbances. Very near the nozzle, distinct vortical structures are evident that are associated with the separating inner and outer annulus shear layers. Their relative phasing on the left and right side of the burner annulus changes by 180° under conditions where the burner centerline is nominally at a transverse acoustic velocity node and antinode. These suggest that the dominant excited instability mode of the annular jet changes from axisymmetric to helical as the structure of the acoustic mode shape changes. Farther downstream, these structures disappear rapidly and the disturbance field is dominated by the longer wavelength, transverse acoustic field.
1 April 2014 in SAE International Journal of Engines
Post injections have been shown to reduce engine-out soot emissions in a variety of engine architectures and at a range of operating points. In this study, measurements of the engine-out soot from a heavy-duty optical diesel engine have conclusively shown that interaction between the post-injection jet and soot from the main injection must be, at least in part, responsible for the reduction in engine-out soot. Extensive measurements of the spatial and temporal evolution of soot using high-speed imaging of soot natural luminosity (soot-NL) and planar-laser induced incandescence of soot (soot-PLII) at four vertical elevations in the piston bowl at a range of crank angle timings provide definitive optical evidence of these interactions.The soot-PLII images provide some of the most conclusive evidence to date that the addition of a post injection dramatically changes the topology and quantity of in-cylinder soot. As the post jet penetrates toward the bowl wall, it carves out regions from the main-injection soot structures, either through displacement of the soot or through rapid and progressive oxidation of the soot. Later in the cycle, the regions of main-injection soot on either side of the jet centerline, clearly present in the main-injection-only case, have all but disappeared when the post-injection is added - only the soot in the post-injection pathway remains. Evidence of this apparent late-cycle oxidation of main-injection soot appears in both the soot-PLII and soot-NL images, providing substantial support for the mixing mechanism of soot reduction with post injections. Implications of these findings and future work are also discussed.