To interpret seismic images, rock seismic velocities need to be calculated at elevated pressure and temperature for arbitrary compositions. This technical report describes an algorithm, software, and data to make such calculations from the physical properties of minerals. It updates a previous compilation and Excel® spreadsheet and includes new MATLAB® tools for the calculations. The database of 60 mineral end‐members includes all parameters needed to estimate density and elastic moduli for many crustal and mantle rocks at conditions relevant to the upper few hundreds of kilometers of Earth. The behavior of α and β quartz is treated as a special case, owing to its unusual Poisson's ratio and thermal expansion that vary rapidly near the α‐β transition. The MATLAB tools allow integration of these calculations into a variety of modeling and data analysis projects.
16 August 2014 in Geochemistry, Geophysics, Geosystems
Seismic attenuation measurements provide a powerful tool for sampling mantle properties. Laboratory experiments provide calibrations at seismic frequencies and mantle temperatures for dry melt-free rocks, but require ∼102−103 extrapolations in grain size to mantle conditions; also, the effects of water and melt are not well understood. At the same time, body wave attenuation measured from dense broadband arrays provides reliable estimates of shear wave attenuation ( ), affording an opportunity for calibration. We reanalyze seismic data sets that sample arc and back-arc mantle in Central America, the Marianas, and the Lau Basin, confirming very high attenuation (QS ∼ 25–80) at 1 Hz and depths of 50–100 km. At each of these sites, independent petrological studies constrain the temperature and water content where basaltic magmas last equilibrated with the mantle, 1300–1450°C. The QS measurements correlate inversely with the petrologically inferred temperatures, as expected. However, dry attenuation models predict QS too high by a factor of 1.5–5. Modifying models to include effects of H2O and rheology-dependent grain size shows that the effects of water-enhanced dissipation and water-enhanced grain growth nearly cancel, so H2O effects are modest. Therefore, high H2O in the arc source region cannot explain the low QS, nor in the back arc where lavas show modest water content. Most likely, the high attenuation reflects the presence of melt, and some models of melt effects come close to reproducing observations. Overall, body wave QS can be reconciled with petrologic and laboratory inferences of mantle conditions if melt has a strong influence beneath arcs and back arcs.
At most mid-ocean ridges, a wide region of decompression melting must be reconciled with a narrow neovolcanic zone and the establishment of full oceanic crustal thickness close to the rift axis. Two competing paradigms have been proposed to explain melt focusing: narrow mantle upwelling due to dynamic effects related to in situ melt or wide mantle upwelling with lateral melt transport in inclined channels. Measurements of seismic attenuation provide a tool for identifying and characterizing the presence of melt and thermal heterogeneity in the upper mantle. We use a unique data set of teleseismic body waves recorded on the Cascadia Initiative’s Amphibious Array to simultaneously measure seismic attenuation and velocity across an entire oceanic microplate. We observe maximal differential attenuation and the largest delays ( s and δTS ~ 2 s) in a narrow zone <50 km from the Juan de Fuca and Gorda ridge axes, with values that are not consistent with laboratory estimates of temperature or water effects. The implied seismic quality factor (Qs ≤ 25) is among the lowest observed worldwide. Models harnessing experimentally derived anelastic scaling relationships require a 150-km-deep subridge region containing up to 2% in situ melt. The low viscosity and low density associated with this deep, narrow melt column provide the conditions for dynamic mantle upwelling, explaining a suite of geophysical observations at ridges, including electrical conductivity and shear velocity anomalies.
The plate interface undergoes two transitions between seismogenic depths and subarc depths. A brittle-ductile transition at 20–50 km depth is followed by a transition to full viscous coupling to the overlying mantle wedge at ∼80 km depth. We review evidence for both transitions, focusing on heat-flow and seismic-attenuation constraints on the deeper transition. The intervening ductile shear zone likely weakens considerably as temperature increases, such that its rheology exerts a stronger control on subduction-zone thermal structure than does frictional shear heating. We evaluate its role through analytic approximations and two-dimensional finite-element models for both idealized subduction geometries and those resembling real subduction zones. We show that a temperature-buffering process exists in the shear zone that results in temperatures being tightly controlled by the rheological strength of that shear zone’s material for a wide range of shear-heating behaviors of the shallower brittle region. Higher temperatures result in weaker shear zones and hence less heat generation, so temperatures stop increasing and shear zones stop weakening. The net result for many rheologies are temperatures limited to ≤350–420 °C along the plate interface below the cold forearc of most subduction zones until the hot coupled mantle is approached. Very young incoming plates are the exception. This rheological buffering desensitizes subduction-zone thermal structure to many parameters and may help explain the global constancy of the 80 km coupling limit. We recalculate water fluxes to the forearc wedge and deep mantle and find that shear heating has little effect on global water circulation.
13 March 2020 in Geochemistry, Geophysics, Geosystems
We present new 3‐D P wave and S wave velocity models of the upper 20 km of the Mount St. Helens (MSH) region. These were obtained using local‐source arrival time tomography from earthquakes and explosions recorded at 70 broadband stations deployed as part of the imaging Magma Under St. Helens (iMUSH) project and augmented by several data sets. Principal features of our models include (1) low P wave and S wave velocities along the St. Helens seismic zone to depths of at least 20 km corresponding to high conductivity imaged by iMUSH magnetotelluric studies. This delineates a zone of weakness that magma can exploit at the location of MSH; (2) a 5‐ to 7‐km diameter, 6–15 km deep, 3–6% negative P wave and S wave velocity anomaly beneath MSH, consistent with previous estimates of the source region for recent eruptions. We interpret this as a magma storage region containing up to 15–20 km3 of partial melt, which is about 5 times more than the largest documented eruption at MSH; (3) a broad region of low P wave velocity below 10‐km depth extending between Mount Adams and Mount Rainier along and to the east of the main Cascade arc, which is likely due to high‐temperature arc crust and possible presence of fluids or melt; (4) several anomalies associated with surface‐mapped features, including high‐velocity igneous units such as the Spud Mountain and Spirit Lake plutons and low velocities in the Chehalis sedimentary basin and the Indian Heaven volcanic field. Our results place further constraints on the geometry of these features at depth.