30 October 2023 in IEEE Transactions on Instrumentation and Measurement
Nonlinear friction, uncertainties and external disturbances always exist in two-axis opto-electronic tracking and measuring system, which reduces the control accuracy of the system. In this paper, a robust adaptive integral sliding mode control (RAISMC) strategy based on novel nonlinear extended state observer (NNESO) is proposed for high precision motion control of this nonlinear servo system. The proposed controller comprises improved nonlinear ESO, integral sliding mode control and robust adaptive control methods. By modifying the fal function to eliminate the discontinuity of ESO, a novel nonlinear observer is obtained to measure and estimate the disturbances, uncertainties and states of the system. The integral sliding mode control strategy is combined with the novel nonlinear observer and robust adaptive control to compensate (cancel) the effects of nonlinear friction, uncertainties and external disturbances. The stability of the opto-electronic tracking system is proved by Lyapunov theory. Comparative simulation and actual experiments are implemented on the opto-electronic tracking system, and the results verify the superiority and effectiveness of RAISM control scheme with NNESO, which is superior to the existing state-of-the-art method.
25 April 2017 in IEEE Transactions on Circuits and Systems II: Express Briefs
A traditional flyback LED driver is limited by its low performance, which usually does not meet the power factor (PF) and total harmonic distortion requirements according to Energy Star or IEC61000-3-2. The control loop from the secondary side to the primary side has low reliability and employs more components, which reduces the power density of the system and increases the cost. In this brief, based on single-stage single ended primary inductor converter (SEPIC) and flyback converter, a primary-side-regulated LED driver is proposed to improve the performance of the system. Working in DCM, the SEPIC circuit realizes the PF correction naturally. For the flyback converter, the proposed primary-side-regulated method improves the power density and guarantees accurate control of the output current. A 100-W prototype based on SEPIC-flyback was built to verify the analysis and the experimental results coincided with the analysis results satisfactorily.
21 August 2018 in IET Power Electronics
This study presents an integrated‐stage AC–DC lighting‐emitting diode (LED) driver based on flyback and Class‐E converter with high power factor (PF) with a wide range of the duty cycle. The flyback circuit works in discontinuous conduction mode to realise the PF correction function, and the Class‐E circuit is used as DC–DC converter to transfer the energy to the LED load. By sharing the common switch of the two circuits, the cost of system can be decreased distinctly. In addition, the Class‐E converter provides soft‐switching operation in a resonant mode, which can improve the converter efficiency. By integrating the flyback and Class‐E converters, the soft‐switching characteristic is still kept. In addition, the LED driver can be operated with wide duty cycle range to achieve a design degree of freedom to regulate the output current at a constant working frequency which makes the design of EMI filter easier. The operational principles, detailed analysis and design considerations of the LED driver are presented. A 100 W prototype is presented in an experimental condition to certifying the validity of the proposed integrated‐stage LED driver.
20 June 2023 in IEEE Transactions on Power Electronics
Power converters powered by batteries have been widely used in many applications, such as outdoor emergency lighting, electric motorcycle charger, unmanned aerial vehicle supply, and so on. This article presents a 500-kHz zero-voltage switching (ZVS) Class-E type dc–dc converter with two anti-series mosfet s used for battery-powered applications. The low-side mosfet is adopted as the main switch to realize the working operation of traditional Class-E resonant converter, while the high-side anti-series mosfet is used to implement the regulation of the converter output voltage based on pulsewidth modulation. Both active switches are ZVS operated so that a high efficiency can be achieved. By changing the high-side mosfet duty cycle, the ac voltage of the resonant tank is also changed to regulate the output voltage consequently. The control method is simple, and the operating frequency is constant, which is beneficial for the design of the resonant components. A 100-W prototype is built to verify the validity of the proposed control method for which a 94.85% efficiency has been achieved.