1 November 2004 in Journal of Structural Engineering
The paper reports progress in the development of a practical probabilistic model for the estimation of expected annual damage induced by hurricane winds in residential structures. The estimation of the damage is accomplished in several steps. First, basic damage modes for components of specific building types are defined. Second, the damage modes are combined in possible damage states, whose probabilities of occurrence are calculated as functions of wind speeds from Monte Carlo simulations conducted on engineering numerical models of typical houses. The paper describes the conceptual framework for the proposed model, and illustrates its application for a specific building type with hypothetical probabilistic input. Actual probabilistic input must be based on laboratory studies, postdamage surveys, insurance claims data, engineering analyses and judgment, and Monte Carlo simulation methods. The proposed component-based model is flexible and transparent. It is therefore capable of being readily scrutinized....
1 November 2016 in Journal of Structural Engineering
The lack of a standard accepted method to estimate local peak pressure coefficients from wind tunnel data can lead to inconsistent definitions and interpretations, particularly because cost and time constraints associated with wind tunnel tests of low-rise buildings necessitate relatively short (equivalent full-scale) durations. This paper focuses on a Gumbel distribution fitting method widely used in practice. Because the sources of uncertainty regarding estimated peaks include the use of short-duration records (in practice) and the assumption that the observed peaks from wind tunnel pressure data are Gumbel-distributed, this is quantified in detail in terms of the parameters determining the required minimum record length. It is shown that 15 observed peaks can lead to local peak pressure estimates with adequate precision for many design scenarios. However, the conversion of peak coefficients from a short duration to those of a longer duration requires an increase in the number of observed peaks ...
1 November 2011 in Natural Hazards Review
Florida’s population growth in recent decades has produced a steady increase in the concentration of population and infrastructure along its coastline. During this growth period, the vulnerability of the Florida coastline to hurricane impact has been amply demonstrated. The aftermaths unveiled the underlying potential for dramatic economic loss, which is disruptive for the state economy and has created a crisis in the property insurance market. To aid in preparedness efforts, the state of Florida commissioned a group of experts to develop the Florida Public Hurricane Loss Model (FPHLM). This paper describes how hurricane damage prediction techniques were developed and implemented in the vulnerability module of the FPHLM. The module consists of an external damage simulation engine coupled with internal damage and contents damage simulation engines. These components are described in this paper.
1 November 2011 in Natural Hazards Review
The state of Florida has about $1.8 trillion worth of residential property at risk of hurricane induced loss, and the hurricanes of the past few years have created a crisis in the homeowner insurance market. There is great uncertainty about the nature of the risk and the potential losses for the state as well as the insurance and reinsurance industries, and rates have consequently increased dramatically. This paper discusses the nature and use of a public catastrophe model to assess hurricane risk and estimate potential losses. It briefly explains the model design and then presents estimates of the average annual insured losses and probable maximum insured losses for the state of Florida. It also presents scenario-based loss estimates for Category 1 through 5 hurricanes land-falling at various locations in the state. The average annual insured loss for the residential properties in the state of Florida is estimated to be around $5 billion before deductibles and $3 billion after deductibles. And a 50-year ...
16 September 2020 in Frontiers in Built Environment
PFPedro L. Fernández-Cabán
+1
The Natural Hazards Engineering Research Infrastructure (NHERI) experimental facility at the University of Florida provides a diverse suite of experimental resources to support wind hazard research. The 40-m long Boundary Layer Wind Tunnel (BLWT) simulates boundary layer flows to characterize wind loading on rigid structural models and assess the response of aeroelastic structures. The use of experimental automation tools provides researchers unparalleled flexibility in their test configurations while supporting high throughput testing and data collection. The Terraformer, an array of 1116 roughness elements, can be rapidly reconfigured to generate terrain conditions in less than 90 s, the test section turntable can move automatically through a range of wind approach angles, and the instrumentation gantry can traverse preset paths to collect wind field measurements anywhere in the tunnel cross-section. These test automation tools, along with mechatronic structural models and real-time data transfer and processing, provide new opportunities in experimental wind tunnel testing. Recent cyber-physical wind tunnel testing projects highlight the benefits of these experimental automation tools. This paper will also discuss the most recent addition to the BLWT, the Flow Field Modulator (FFM). It consists of a 2D array of 319 individually controlled ducted fans driven by electronic speed controllers. The FFM expands the BLWT capabilities by supporting the simulation of non-monotonic profiles and non-stationary events such as gust fronts and downbursts, where mean velocity and turbulence distributions change over short spatial scales. The ability to simulate these flow conditions in a wind tunnel enables the investigation of a wide range of damaging conditions and the solutions for mitigating their impact on structures.
24 January 2024 in Reliability Engineering & System Safety