10 November 2021 in IEEE Transactions on Components, Packaging and Manufacturing Technology
In modern society, electronic equipment continues to develop in the direction of miniaturization and multifunction. In order to meet this requirement, packaging technology has gradually evolved from “2-D planar packaging” to “3-D packaging.” The realization of the flip-chip bonding process and the thermal cycle reliability of the 3-D stacked structure are discussed in this article. First, to stack three substrates and a small size chip together, the flip-chip bonding machine was used to vertically stack the chips in the $Z$ -direction. Then, the finite element software was used to analyze the thermal stress distribution of the overall structure under the thermal cycle load, and the life of the critical solder joints in the package was predicted. The simulation results show that, compared to the solder joints between the substrates, the copper pillar bumps of the small-size chip had a longer life.
28 July 2022 in IEEE Transactions on Components, Packaging and Manufacturing Technology
We adopted a novel method to achieve a high-density microbump connection through microsilver paste sintering at low temperature quickly with the help of ultrasonic. Sliver paste sintering with its unique performance has the potential as an alternative to Pb-free solder and this has been generally accepted. However, it has not been applied in the field of high-density bump interconnection. The usual sintering problem is time-consuming, porous, and low wettability. Many sintering experiments were carried out in two copper plates, focusing on the study of the sintering mechanism. We conduct our research in a manner that is the closest to production, which will be helpful to production. We solving the problem that how to coat sliver paste on a high-density small space microbump uniformly. In this article, the vibration of ultrasonic, sintering curve, shear strength, fracture surface, and cross section were studied to help understand the fundamental mechanism. Experiments show that ultrasonic vibration increases the density of silver particles and generates a certain amount of frictional heat, promoting the adjacent nanoparticles to become agglomerated or aggregated. We can conclude that it can achieve Cu–Cu robust fast interconnection at low temperature by microsilver paste sintering with the appropriate sintering method and the suitable process. This study provides a possible method for the copper pillar microbump interconnection.
26 April 2023 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Thermosonic flip chip (TSFC) bonding technology has become a developing area of chip packaging technology due to its advantages of low bonding temperature and bonding pressure. To explore the appropriate bonding parameters and to understand the relationship between each parameter and the stress/strain at the bonding interface. Bonding tests were carried out and then simulated orthogonal tests were conducted using the finite element model. The bonding test results show that: The initial position of the bumps does not affect the strength after bonding. But, an unreasonable selection of bonding pressure and ultrasonic parameters can lead to different degrees of cracks at the bonding interface after bonding and destroy the bonding strength. Simulation results show that: The order of influence of the three bonding parameters on von Mises stress/(shear stress) is: bonding pressure> ultrasonic amplitude>bonding temperature/(ultrasonic amplitude>bonding temperature>bonding pressure). Based on the simulation results, a multivariate nonlinear regression model between von Mises stress/shear stress and bonding parameters was constructed. Some recommendations for the selection of bonding parameters are given: 1 ) the bonding pressure was selected in the range of 9-11MPa, 2)the bonding temperature was chosen to be less than 200 °C and 3) the ultrasonic amplitude was 1.1μm(power about 22w). At the same time, the ultrasonic power can be increased by increasing the ultrasonic frequency to achieve better results in bonding. This study can provide some theoretical basis for the selection of bonding parameters for TSFC bonding.
30 November 2020 in IEEE Transactions on Components, Packaging and Manufacturing Technology
In order to understand the influence of the Kovar-4J29 cylinder height on ultrasonic wire bonding, it was studied by the finite-element method (FEM). Explicit Dynamics was used to simulate the bonding process. And the modal frequencies and response deformations of the cylinder with different heights were also carried out. The results showed that the lower interfacial activation energy due to resonance resulted in a successful bonding between the gold ball and the Kovar-4J29 cylinder. Furthermore, a generalized pattern search (GPS) algorithm was utilized to optimize the height of the cylinder to obtain a better bonding effect, followed by re-simulation of the optimized model. This study could provide guidance for further bonding experiments between gold balls and Kovar-4J29 cylinder.
22 November 2021 in Journal of Electronic Packaging
Silicon piezoresistive pressure sensors can only operate below 125 °C due to the leakage current of the PN junction. However, silicon-on-insulator (SOI) high-temperature pressure sensors use SiO2 for total dielectric isolation to solve this problem. At present, SOI high-temperature pressure sensors mostly use lead bonding package structure, with gold wire to lead the electrical signal and silicone oil as the protection medium, but the working temperature of silicone oil is limited to about 150 °C. In this paper, the leadless package structure is designed using pressure conduction on the backside of the chip and replacing the gold wire with sintered silver paste. The materials and dimensions of the leadless package structure are determined and then obtained a complete package structure through manufacturing. The reliability of the leadless package structure after silver paste sintering was verified by finite element analysis, and the results showed that the thermal stress caused by high and low-temperature cycles in the leadless package is minimal and does not affect the sensitivity of the pressure-sensitive chip. The size of the leadless package structure was optimized by Taguchi orthogonal method, and the maximum thermal stress was effectively reduced. Also, the key factors affecting the thermal stress of the leadless package in the package structure were identified by the variance number analysis method. The optimized leadless package structure size was remanufactured, and the sintered package structure was tested. The data show that the sensitivity of the pressure sensor is 30.82 mV/MPa with a nonlinearity of less than 0.4% full-scale (FS).
1 July 2020 in International Journal of Agricultural and Biological Engineering
Creep and relaxation characteristics of stem for rice seedlings grown in plastic cell tray were studied by static tensile testing, in order to determine the relationship between characteristic parameters (rheological model parameters, stress components and strain components) and test levels (stress levels and strain levels). Rice seedling stem specimen used in the test was 40 mm in length. And the applied test values for the creep and relaxation test ranged from 1.0-3.0 MPa and 1.5%-3.5%, respectively, each for 5 levels. The results indicated that elastic modulus in the creep and relaxation model was not affected by test levels. However, except that viscosity coefficient eta(kv), was a constant and eta(m1) decreased with the increase of test levels, other viscosity coefficient and rheological time nonlinearly increased as the test levels increased. And strain components in the creep model and stress components in the relaxation model significantly increased as the test levels increased.