Yun Jiang

Yun Jiang

Auto-generated profile, based on publicly available information

Yun Jiang

Department of Microwave Research Hunan Vanguard Group Co. Ltd., Changsha 410137, China

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 November 2021 in IEEE Microwave and Wireless Components Letters
Verified
Journal Article
Closed access
YJYun Jiang
Yun Jiang
ZHZhaoyu Huang
Zhaoyu Huang
BLBoyuan Liu
Boyuan Liu
XZXiaofa Zhang
Xiaofa Zhang
CWChao Wang
Chao Wang
NYNaichang Yuan
Naichang Yuan
This letter presents a novel but very simple W-band E-plane waveguide bandpass filter (BPF) using just one compact beeline resonator (CBR), which leads to multiple transmission zeros (TZs). The proposed filter with low insertion loss (IL) and high selectivity is only 3.21 mm in length of the E-plane substrate. For further demonstration, a filter example with center frequency at $f_{0} =$ 88.55 GHz is implemented with generation of three TZs for theoretically calculated certification. Moreover, the measured minimum IL is only 1.15 dB. Good agreement between simulations and measurements validates the design method.

31 December 2024 in Applied Computational Electromagnetics Society Journal (ACES)
Verified
Journal Article
Open access
PDF file
ZCZichong Chen
Zichong Chen
RYRui Yin
Rui Yin
YJYun Jiang
Yun Jiang
XMXiaojun Mao
Xiaojun Mao
PLPengjie Lv
Pengjie Lv
YLYang Liu
Yang Liu
In this paper, the evolutionary process, fabrication and measurement of an all-metal antipodal Vivaldi antenna (AMAVA) design are presented for the high-power microwave (HPM) application. Derived from the substrate-loaded antipodal Vivaldi antenna, the proposed antenna is made all metallic to enhance its power handling capacity (PHC). Considering the further improvement of the radiation performance and antenna fixing, rectangular slots and tuning stubs with exponential corner cuts are employed in antenna design. In the air condition, the PHC values of the final proposed antenna are over 8000 W in its operating band. The proposed AMAVA is fabricated and measured in a microwave anechoic chamber. According to the measured results, the −10 dB impedance bandwidth covers 8.3-10.66 GHz, and its deepest resonance reaches −29.7 dB at 9.75 GHz. The measured radiation pattern values are in agreement with simulation values, and its peak gain values at 9.3 GHz, 9.8 GHz and 10.3 GHz are 4.54 dBi, 5.68 dBi and 5.71 dBi, respectively. A PHC experiment is conducted, which verifies the AMAVA is qualified for 8000 W-level PHC.

19 August 2021 in Applied Computational Electromagnetics Society Journal (ACES)
Verified
Journal Article
Closed access
PDF file
YYYuan Ye
Yuan Ye
ZHZhao Huang
Zhao Huang
YJYun Jiang
Yun Jiang
LBLi-An Bian
Li-An Bian
CZChang Zhu
Chang Zhu
NYNai Yuan
Nai Yuan
A low profile ultra-wideband tightly coupled dipole array is studied. The antenna elements are fed by Marchand baluns of small size and low cost. A metasurface based wide-angle impedance matching (MSWAIM) layer is introduced to replace the traditional dielectric WAIM, improving the beam scan performance and reducing the antenna profile. The simulation shows that the proposed antenna array can operate over 2.4-12.4 GHz, approximately 5:1 bandwidth with maximum scanning angle of 50o for both E plane and 45o for H plane. The antenna profile above the ground is only 0.578λH at the highest operating frequency. This antenna array can find its application in the forthcoming massive MIMO beamforming systems for 5G.

28 November 2021
Verified
Conference Paper
Closed access
BLBo. Yuan. Liu
Bo. Yuan. Liu
PJPeng. Fei. Ji
Peng. Fei. Ji
WYWen. Tao. Yuan
Wen. Tao. Yuan
ZHZhao. Yu. Huang
Zhao. Yu. Huang
YJYun. Jiang
Yun. Jiang
NYNai. Chang. Yuan
Nai. Chang. Yuan
Large scale integrated circuit (IC), where the down-conversion circuit usually acts as the main chain of receiving channel, requires appropriate miniaturized filter as one of the most important units to effectively suppress mirror frequency caused by front-end mixing process to some extent. MEMS (Micro Electro Mechanical System) chip technology is introduced for its greater performance and reliability in lower power consumption and a smaller volume. In this paper, starting with the analysis of the structure and characteristics of the filter chip, the MEMS filter’s advantages over the traditional structure and structural features are described, and a X-band MEMS filter is designed through calculation, modeling and simulation in sequence, to furtherly contribute to mixing channel with high suppression on unwanted signal frequency. The MEMS filter satisfies demands of miniaturization and integration, conforming to the chip technology development, which is suitable for popularity in practical applications.