Yiwei Qin

Yiwei Qin

Auto-generated profile, based on publicly available information

Yiwei Qin

Department of Electric Engineering, Shenyang University of Technology, Shenyang, China

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 October 2024 in IEEE Transactions on Energy Conversion
Verified
Journal Article
Closed access
RPRuilin Pei
Ruilin Pei
ZLZhiye Li
Zhiye Li
YLYuxiao Li
Yuxiao Li
YQYiwei Qin
Yiwei Qin
WLWeizhou Li
Weizhou Li
LZLubin Zeng
Lubin Zeng
High saturation flux density, high permeability and low specific core loss in the rolling direction (RD) are the characteristics of anisotropic soft magnetic materials. In order to meet the requirements of high torque density, high power density and high efficiency for the electric vehicle traction electric motor, the application of anisotropic silicon steel, i.e., grain oriented electrical steel (GOES) sheets in traction electric motor is investigated in this paper. Firstly, Ultra-thin anisotropic silicon steel sheets are selected based on the analysis of material properties and the reduction of eddy current losses in the core. Then, the performance of the tooth-yoke spliced PMSM, which is superior to the conventional non-grain-oriented electrical steel (NGOES) sheet PMSM in terms of torque and efficiency, is analyzed using the finite element method (FEM). And the design of experiment and analysis of the results proved that the circular splice pattern of the motor tooth was superior to the dovetail splice. Finally, a GOES PMSM is manufactured for verification. It is revealed that the measured current amplitude of the GOES PMSM is about 6.06% lower than that of the NGOES PMSM under the same geometric parameters and rated output torque. When the electric motor is operating, as the speed increases, the efficiency and torque of the GOES motor are higher than those of the NGOES PMSM throughout the motor's operating range.

15 May 2024 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
ZLZhiye Li
Zhiye Li
YLYuxiao Li
Yuxiao Li
YQYiwei Qin
Yiwei Qin
LZLubin Zeng
Lubin Zeng
JLJun Li
Jun Li
RPRuilin Pei
Ruilin Pei
In permanent magnet synchronous motors (PMSMs), grain-oriented electrical steels (GOESs), which have high permeability, high saturation flux density, and low core losses in the rolling direction (RD), are gradually being used to increase power/torque density and efficiency. In radial flux PMSM, the use of GOES tooth–yoke assemblies introduces a parasitic air gap, which leads to a change in the magnetomechanical characteristics at the position. In order to explore the effect of different shapes of parasitic air gap and to adopt a good splicing method, this article investigates the Maxwell stress and material properties at the parasitic air gap in dovetail and circular splices. First, the electric motor performances of two kinds of spliced tooth with GOES are calculated by the finite element method (FEM), and then, the Maxwell stress distributions at the parasitic air gaps are calculated, and the tensile stresses generated by different shapes of the parasitic air gaps are analyzed. The maximum stress at the parasitic air gap appears on both edges of the tooth, and the magnitude and waveform of the tensile stress are dependent on the shape of the parasitic air gap. The circular parasitic air gap can generate a maximum tensile stress of 1.4 mPa, and the stress distribution at the center of the tooth of the circular parasitic air gap is similar to a sinusoidal function. Experiments have shown that tensile stresses of 0–2 mPa can improve the material properties, which is due to the tensile stresses compensating the internal compressive stresses generated by the negative magnetostriction in the magnetization process. According to the comprehensive consideration of stress-magnetic interaction and performance changes, it is proved that the air gap, which can produce large tensile stress, is more suitable for tooth splicing structure, which guides the application of GOES in motor.

26 September 2024 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
ZLZhiye Li
Zhiye Li
YLYuxiao Li
Yuxiao Li
YQYiwei Qin
Yiwei Qin
LZLubin Zeng
Lubin Zeng
JLJun Li
Jun Li
RPRuilin Pei
Ruilin Pei
Presents corrections to the paper, Analysis of Magnetomechanical Properties at the Tooth–Yoke Embedding Position in Grain-Oriented Electrical Steel Electric Motors.