In simply-supported reinforced-concrete (RC) beams strengthened by carbon-fiber-reinforced polymer (CFRP) plates, plate debonding is initiated at the beam ends, where the principal compression, predominantly composed of a vertical component, detaches the plate externally bonded to the unconfined cover concrete. A CFRP wrap acting as a U-clamp can provide confinement to enhance the moment capacity by resisting premature cover debonding. The wrap design parameters in terms of clamping location, width, and stiffness were identified from a set of fundamental experiments. The ultimate moment capacities of 22 tested specimens with different end anchorage conditions were compared against control specimens. The debonding strain, and consequently the ultimate moment capacity, gradually increased with increasing U-clamp width and stiffness. The failure patterns confirmed the effect of U-clamps in inducing a partial confinement effect on the sides and bottom of a beam end. The resulting changes in the compre...
1 January 2016 in Construction and Building Materials
Finite element models are analyzed and validated with the experimental shear capacities of steel fiber reinforced concrete (SFRC) as well as plain concretes. In this work, steel fibers with low aspect ratio which are commonly available in Bangladesh are used and sufficient capacity enhancements are attained. Two different aggregate types are used to make the SFRC and plain concrete beam specimens, i.e. stone and brick, and also modelled in the finite element (FE) platform of ANSYS 10.0 with SOLID65 element. The experimental plan intended to investigate the shear capacity enhancement of three different types of beam specimens, i.e. single shear, double shear and flexural shear. All the specimens are tested in the 1000kN capacity digital universal testing machine (UTM) and the strain data are obtained from digital image correlation technique (DICT) using high definition (HD) images and high speed video clips. Test results showed the increase in shear capacity of about 30% to 170% of beams made of SFRC with an indication of increase in ductility. FE models are analyzed extensively and validated with the experimental stress-strain behaviours by optimizing the Poisson's ratio, modulus of elasticity, tensile capacity and stress-strain behaviours. FE models showed the same structural response and failure modes as found in experimental investigation. This paper can contribute to the construction industry of Bangladesh about SFRC with reliable experimental data and FE analyses
Plain concrete and steel fiber reinforced concrete (SFRC) cylinder specimens are modeled in the finite element (FE) platform of ANSYS 10.0 and validated with the experimental results and failure patterns. Experimental investigations are conducted to study the increase in compressive and tensile capacity of cylindrical specimens made of stone and brick concrete and SFRC. Satisfactory compressive and tensile capacity improvement is observed by adding steel fibers of 1.5% volumetric ratio. A total of 8 numbers of cylinder specimens are cast and tested in 1000 kN capacity digital universal testing machine (UTM) and also modeled in ANSYS. The enhancement of compressive strength and splitting tensile strength of SFRC specimen is achieved up to 17% and 146%, respectively, compared to respective plain concrete specimen. Results gathered from finite element analyses are validated with the experimental test results by identifying as well as optimizing the controlling parameters to make FE models. Modulus of elasticity, Poisson’s ratio, stress-strain behavior, tensile strength, density, and shear transfer coefficients for open and closed cracks are found to be the main governing parameters for successful model of plain concrete and SFRC in FE platform. After proper evaluation and logical optimization of these parameters by extensive analyses, finite element (FE) models showed a good correlation with the experimental results.
20 October 2016 in Advances in Materials Science and Engineering
Available codes and models generally use partially modified shear design equation, developed earlier for steel reinforced concrete, for predicting the shear capacity of FRP-RC members. Consequently, calculated shear capacity shows under- or overestimation. Furthermore, in most models some affecting parameters of shear strength are overlooked. In this study, a new and simplified shear capacity prediction model is proposed considering all the parameters. A large database containing 157 experimental results of FRP-RC beams without shear reinforcement is assembled from the published literature. A parametric study is then performed to verify the accuracy of the proposed model. Again, a comprehensive review of 9 codes and 12 available models is done, published back from 1997 to date for comparison with the proposed model. Hence, it is observed that the proposed equation shows overall optimized performance compared to all the codes and models within the range of used experimental dataset.