Osman A. Basaran

Osman A. Basaran

Auto-generated profile, based on publicly available information

Osman A. Basaran

Purdue University, Davidson School of Chemical Engineering, 480 Stadium Mall Drive West Lafayette, Indiana 47907-2100, USA

Research Focus & Metrics

Academic Career Length

22Years (2005-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 March 2015 in Proceedings of the National Academy of Sciences
Verified
Journal Article
Closed access
PDF file
JCJosé Rafael Castrejón-Pita
José Rafael Castrejón-Pita
ACAlfonso Arturo Castrejón-Pita
Alfonso Arturo Castrejón-Pita
STSumeet Suresh Thete
Sumeet Suresh Thete
KSKrishnaraj Sambath
Krishnaraj Sambath
IHIan M. Hutchings
Ian M. Hutchings
OBOsman A. Basaran
Osman A. Basaran
Significance: Fluid flows, governed by nonlinear equations, permit formation of singularities. Often, singularities are artifacts of neglecting physical effects. However, free-surface flows exhibit observable singularities including filament pinch-off. As filaments thin, slightly (highly) viscous filaments are expected from theory to transition from an inertial (viscous) regime where viscosity (density) is negligible to an inertial–viscous regime where viscous and inertial effects are important. Previous works show this transition either does not occur or occurs for filament radii well below theoretical predictions. We demonstrate that thinning filaments unexpectedly pass through a number of intermediate transient regimes, thereby delaying onset of the final regime. The findings raise the question if similar dynamical transitions arise in problems that are not necessarily hydrodynamic in nature.

4 March 2013 in Proceedings of the National Academy of Sciences
Verified
Journal Article
Closed access
PDF file
RCRobert T. Collins
Robert T. Collins
KSKrishnaraj Sambath
Krishnaraj Sambath
MHMichael T. Harris
Michael T. Harris
OBOsman A. Basaran
Osman A. Basaran
Drops subjected to strong electric fields emit charged jets from their pointed tips. The disintegration of such jets into a spray consisting of charged droplets is common to electrospray ionization mass spectrometry, printing and coating processes, and raindrops in thunderclouds. Currently, there exist conflicting theories and measurements on the size and charge of these small electrospray droplets. We use theory and simulation to show that conductivity can be tuned to yield three scaling regimes for droplet radius and charge, a finding missed by previous studies. The amount of charge that electrospray droplets carry determines whether they are coulombically stable and charged below the Rayleigh limit of stability or are unstable and hence prone to further explosions once they are formed. Previous experiments reported droplet charge values ranging from 10% to in excess of . Simulations unequivocally show that electrospray droplets are coulombically stable at the instant they are created and that there exists a universal scaling law for droplet charge, .

1 August 2006 in Physics of Fluids
Verified
Journal Article
Closed access
RSRonald Suryo
Ronald Suryo
OBOsman A. Basaran
Osman A. Basaran
Dynamics of formation of a drop of an incompressible Newtonian fluid of viscosity μ1 and density ρ1 from the tip of a tube of radius R1 into a co-flowing immiscible, incompressible Newtonian fluid of viscosity μ2 and density ρ2 that is enclosed in a concentric cylindrical tube of radius R2 are investigated under creeping flow conditions. Transient drop shapes, and fluid velocities and pressures, are calculated numerically by solving the governing Stokes equations with the appropriate boundary and initial conditions using the Galerkin/finite element method for spatial discretization and an adaptive finite difference method for time integration. In accord with previous studies, the primary effect of increasing the ratio of the volumetric injection rate Q̃2 of the outer fluid to that of the inner fluid Q̃1, Qr≡Q̃2∕Q̃1, is shown to be a reduction in the volume of primary drops that are formed. When Qr is small, calculations show that drop formation occurs in a slug flow regime where the primary drops that are about to be formed are elongated axially and occupy virtually the entire cross section of the outer tube. In this slug flow regime, the primary drops at breakup resemble cylinders that are terminated by hemispherical caps and their aspect ratios Lp∕Dp≫1, where Lp denotes their axial lengths and Dp≈2R2 their maximum diameters. As Qr increases, the dynamics are shown to transition to the dripping regime, where the primary drops are more globular, Lp∕Dp∼1, and their radii are of the order of or smaller than R1. As Qr increases, the importance of viscous stress exerted by the outer fluid relative to the surface tension or capillary pressure increases. Thus, the drop length measured from the tube exit to the drop tip at breakup increases while the primary drop volume decreases as Qr increases. When Qr is sufficiently large, viscous stress exerted by the outer fluid induces a recirculating flow within a forming drop. Once Qr exceeds a critical value Qrt, viscous stress exerted by the outer fluid becomes so large that the growing drop takes on a conical shape and a thin fluid jet with a radius that is a few orders of magnitude smaller than that of the radius of the inner tube emanates from its tip. This latter regime of drop breakup, which is henceforward referred to as tip streaming, is remarkably similar to electrohydrodynamic jetting that is seen from the tips of conical drops in electric fields and tip streaming that occurs from the pointed ends of surfactant-covered free drops subjected to linear extensional or shear flows, but takes place here in the absence of electric fields or surfactants. Scaling arguments for fixed a≡R2∕R1 show that for exterior viscous stress to overcome capillary pressure and cause tip streaming, Ca−1<mQr, where Ca≡μ1Q̃1∕γπR12 is the capillary number, γ is the interfacial tension, and m≡μ2∕μ1 is the viscosity ratio. In accordance with the scaling arguments, the computed predictions show that the critical value of the flow rate ratio signaling transition from dripping to tip streaming Qrt varies inversely with m for small to moderate m but becomes independent of both Ca and m as viscosity ratio grows without bound.

1 October 2007 in Physics of Fluids
Verified
Journal Article
Closed access
PDF file
QXQi Xu
Qi Xu
OBOsman A. Basaran
Osman A. Basaran
Motivated by the desire to improve the theoretical understanding of drop-on-demand (DOD) ink-jet printing, a computational analysis is carried out to simulate the formation of liquid drops of incompressible Newtonian fluids from a simple capillary tube by imposing a transient flow rate upstream of the nozzle exit. Since the flow in a typical ink-jet nozzle is toward the nozzle outlet during part of the time and away from the nozzle outlet at other times, an inflow rate is adopted here that captures the essential physics and is given in dimensionless form by Q=(πWe∕2)sinΩt , where We is the Weber number (inertial/surface tension force), Ω is the frequency, and t is time. The dynamics are studied as functions of We , Ω , and the Ohnesorge number Oh (viscous/surface tension force). For a common ink forming from a nozzle of 10μm radius, Oh=0.1 . For this typical case, a phase or operability diagram in (We,Ω) -space is developed that shows that three regimes of operation are possible. In the first regime, where We is low, breakup does not occur, and drops remain pendant from the nozzle and undergo time periodic oscillations. Thus, the simulations show that fluid inertia, and hence We , must be large enough if a DOD drop is to form, in accord with intuition. A sufficiently large We causes both drop elongation and onset of drop necking, but flow reversal is also necessary for the complete evacuation of the neck and capillary pinching. In the other two regimes, at a given Ω , We is large enough to cause drop breakup. In the first of these two regimes, where Wec1<We<Wec2 , DOD drops do form but have negative velocities, i.e., they would move toward the nozzle upon breakup, which is undesirable. In the second breakup regime, where We>Wec2 , not only are DOD drops formed, but they do so with positive velocities.

1 June 2005 in Physics of Fluids
Verified
Journal Article
Closed access
PDF file
OYOzgur E. Yildirim
Ozgur E. Yildirim
QXQi Xu
Qi Xu
OBOsman A. Basaran
Osman A. Basaran
The drop weight method is an accurate yet simple technique for determining surface tension σ . It relies on dripping a liquid of density ρ at a low flow rate Q̃ from a capillary of radius R into air and measuring the combined volumes of the primary and satellite drops that are formed. The method’s origin can be traced to Tate, who postulated that the volume Ṽideal of the drop that falls from the capillary should be given by ρgṼideal=2πRσ , where g is the gravitational acceleration. Since Tate’s law is only an approximation and the actual drop volume Ṽf<Ṽideal , in practice the surface tension of the liquid-air interface is determined from the experimental master curve due to Harkins and Brown (HB). The master curve is a plot of the fraction of the ideal drop volume, Ψ≡Ṽf∕Ṽideal , as a function of the dimensionless tube radius, Φ≡R∕Ṽf1∕3 . Thus, once the actual drop volume Ṽf , and hence Φ , is known, σ is readily calculated upon determining the value of Ψ from the master curve and that Ψ=ρgṼf∕2πRσ . Although HB proposed their master curve more than 80 years ago, a sound theoretical foundation for the drop weight method has heretofore been lacking. This weakness is remedied here by determining the dynamics of formation of many drops and their satellites in sequence by solving numerically the recently popularized one-dimensional (1–d) slender-jet equations. Computed solutions of the 1-d equations are shown to be in excellent agreement with HB’s master curve when Q̃ is low. Moreover, a new theory of the drop weight method is developed using the computations and dimensional analysis. The latter reveals that there must exist a functional relationship between the parameter Φ , where Φ−3 is the dimensionless drop volume, and the gravitational Bond number G≡ρgR2∕σ , the Ohnesorge number Oh≡μ∕(ρRσ)1∕2 , where μ is the viscosity, and the Weber number We≡ρQ̃2∕π2R3σ . When We→0 , the computed results show that Φ depends solely on G . In this limit, a new correlation is deduced which has a simple functional form, G=3.60Φ2.81 , and is more convenient to use than that of HB. The computed results are also used to show how the original drop weight method can be extended to situations where We is finite and resulting drop volumes are not independent of Oh.

11 August 2017 in Physical Review Fluids
Verified
Journal Article
Closed access
PDF file
CAChristopher R. Anthony
Christopher R. Anthony
PKPritish M. Kamat
Pritish M. Kamat
STSumeet S. Thete
Sumeet S. Thete
JMJames P. Munro
James P. Munro
JLJohn R. Lister
John R. Lister
OBOsman A. Basaran
Osman A. Basaran
The coalescence of bubbles and drops plays a central role in nature and industry. During coalescence, two bubbles or drops touch and merge into one as the neck connecting them grows from microscopic to macroscopic scales. The hydrodynamic singularity that arises when two bubbles or drops have just touched and the flows that ensue have been studied thoroughly when two drops coalesce in a dynamically passive outer fluid. In this paper, the coalescence of two identical and initially spherical bubbles, which are idealized as voids that are surrounded by an incompressible Newtonian liquid, is analyzed by numerical simulation. This problem has recently been studied (a) experimentally using high-speed imaging and (b) by asymptotic analysis in which the dynamics is analyzed by determining the growth of a hole in the thin liquid sheet separating the two bubbles. In the latter, advantage is taken of the fact that the flow in the thin sheet of nonconstant thickness is governed by a set of one-dimensional, radial extensional flow equations. While these studies agree on the power law scaling of the variation of the minimum neck radius with time, they disagree with respect to the numerical value of the prefactors in the scaling laws. In order to reconcile these differences and also provide insights into the dynamics that are difficult to probe by either of the aforementioned approaches, simulations are used to access both earlier times than has been possible in the experiments and also later times when asymptotic analysis is no longer applicable. Early times and extremely small length scales are attained in the new simulations through the use of a truncated domain approach. Furthermore, it is shown by direct numerical simulations in which the flow within the bubbles is also determined along with the flow exterior to them that idealizing the bubbles as passive voids has virtually no effect on the scaling laws relating minimum neck radius and time.