In order to apply power electronics systems to applications such as superconducting systems under cryogenic temperatures, it is necessary to investigate the characteristics of different parts in the power electronics system. This article reviews the influence of cryogenic temperature on power semiconductor devices including Si and wide bandgap switches, integrated circuits, passive components, interconnection and dielectric materials, and some typical cryogenic converter systems. Also, the basic theories and principles are given to explain the trends for different aspects of cryogenically cooled converters. Based on the review, Si active power devices, bulk Complementary metal-oxide-semiconductor (CMOS) based integrated circuits, nanocrystalline and amorphous magnetic cores, NP0 ceramic and film capacitors, thin/metal film and wirewound resistors are the components suitable for cryogenic operation. Pb-rich PbSn solder or In solder, classic printed circuit boards material, most insulation papers and epoxy encapsulant are good interconnection and dielectric parts for cryogenic temperatures.
23 July 2020 in IEEE Transactions on Power Electronics
Zero-Voltage-Switching (ZVS) has been widely applied in wide band gap (WBG) devices based high-switching-frequency converters, for instance, dual-active-bridge (DAB) isolated DC-DC converter, which consists of two H-bridges. To secure ZVS for all eight switches, previous literature mostly focuses on half bridge to analyze switching transitions, which, however, is rather incomplete due to ignoring impact of modulations strategies and cannot fulfill all circumstances. In this letter, the whole H-bridge is used as a unit to analyze ZVS transient process, addressing the ZVS setting in different modulation strategies. The minimal initial inductor energy to complete ZVS process is also pointed out and categorized, which in return can reduce the transformer current thereby enhancing the efficiency. Furthermore, the derivation of accurate ZVS transition time is discussed considering the non-linearity of switch output capacitance, which can be referenced to set up dead-band time. An H-bridge prototype with SiC devices is built up to verify the theory proposed in this letter.
25 October 2019 in IEEE Transactions on Power Electronics
To better support the superconducting propulsion system in the future aircraft applications, the technologies of high-power high switching frequency power electronics systems at cryogenic temperatures should be investigated. This article presents the development of a 40-kW cryogenically cooled three-level active neutral point clamped inverter with 3 kHz output line frequency and 140 kHz switching frequency. Si mosfets are characterized at cryogenic temperatures, and the results show that they have promising performance such as lower on-resistance and switching loss. The design of the inverter is presented in detail with the special consideration of the cryogenic temperature operation. Moreover, a packaging and integration architecture is designed and fabricated to demonstrate the feasibility and performance of the inverter in the lab. It is able to achieve no leakage with good thermal and air insulation. With the inverter and packaging, the experimental results show that the inverter operates properly at cryogenic temperatures. The loss is measured at different load conditions, and the loss analysis is given, which shows that the cryogenically cooled inverter has 30% less loss than operating at room temperature.
28 October 2019 in IEEE Journal of Emerging and Selected Topics in Power Electronics
In order to evaluate the feasibility of newly developed gallium nitride (GaN) devices in a cryogenically cooled converter, this article characterizes a 650-V enhancement-mode GaN high-electron mobility transistor (GaN HEMT) at cryogenic temperatures. The characterization includes both static and dynamic behaviors. The results show that this GaN HEMT is an excellent device candidate to be applied in cryogenic-cooled applications. For example, transconductance at cryogenic temperature (93 K) is 2.5 times higher than one at room temperature (298 K), and accordingly, peak di / dt during turn-on transients at cryogenic temperature is around 2 times of that at room temperature. Moreover, the ON-resistance of the channel at the cryogenic temperature is only one-fifth of that at room temperature. The corresponding explanations of performance trends at cryogenic temperatures are also given from the view of semiconductor physics. In addition, several device failures were observed during the dynamic characterization of GaN HEMTs at cryogenic temperatures. The ultrafast switching speed-induced high di / dt and dv / dt at cryogenic temperatures amplify the negative effects of parasitics inside the switching loop. Based on failure waveforms, two failure modes were classified, and detailed failure mechanisms caused by ultrafast switching speed are given in this article.
2 June 2020 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Three-level converters are more susceptible to parasitics compared with two-level converters because of their complicated structure with multiple switching loops. This paper presents the methodology of busbar layout design for three-level converters based on magnetic cancellation effect. The methodology can fit for 3L converters with symmetric and asymmetric configurations. A detailed design example is provided for a high power three-level active neutral point clamped (ANPC) converter, which includes the module selection, busbar layout, and DC-link capacitor placement. The loop inductance of the busbar is verified with simulation, impedance measurements, and converter experiments. The results match with each other, and the inductances of short and long loops are 6.5 nH and 17.5 nH respectively, which are significantly lower than the busbars of NPC type converters in other references.
5 September 2019 in IEEE Transactions on Power Electronics
Paralleling three phase three-level inverters is gaining popularity in industrial applications. However, analytical models for the harmonics calculation of a three-level neutral point clamped (NPC) inverter with popular space vector modulation (SVM) are not found in the literature. Moreover, how interleaving angle impacts the dc- and ac-side harmonics and electromagnetic interference (EMI) harmonics in parallel interleaved three-level inverters and how to optimize interleaving angle to reduce these harmonics have not been discussed in the literature. Furthering previous study, this article presents the modeling, analysis, and reduction of harmonics in paralleled and interleaved three-level NPC inverters with SVM. Analytical models for harmonic calculation are developed, and the dc-side harmonics characteristics of an NPC inverter are identified. The impact of interleaving angle on the ac-side voltage and dc-link current harmonics of parallel interleaved three-level NPC inverters is comprehensively studied. The impact of switching frequency and interleaving angle on EMI harmonics is also illustrated. Optimal interleaving angle ranges to reduce these harmonics are derived analytically. The developed models and harmonic reduction analysis are verified experimentally with two paralleled and interleaved three-level NPC inverters.