20 November 2023 in IEEE Transactions on Power Electronics
Piezoelectric power conversion has emerged as a promising technology for power-dense, efficient dc–dc conversion absent of magnetic components for energy storage. However, two practical challenges of piezoelectric devices have limited prototype demonstrations to relatively low power. First, spurious resonant modes plague low impedance resonator design, restricting operating load range, and lowering efficiency. Second, the mechanical nature of piezoelectric energy storage prevents traditional methods of removing heat. This work presents a spurious-free piezoelectric resonator design and a FOM for measuring a power resonator's spurious modes. Additionally, this work develops thermal enhancements at both the piezoelectric device and converter level to improve heat extraction. These advances in acoustic and thermal performance overcome the challenges for moving piezoelectric power conversion to high power, demonstrated by a paralleled piezoelectric dc–dc converter capable of outputting 3.2 kW at 97.7% efficiency, and a piezoelectric resonator achieving a component power density of 5.7 kW/cm $^{3}$ .
16 November 2021 in IEEE Open Journal of Power Electronics
JSJeronimo Segovia-Fernandez
Jeronimo Segovia-Fernandez
+1
Piezoelectric resonators have shown promise as efficient, power-dense energy storage element alternatives to continue the miniaturization of DC-DC converters. However, practical piezoelectric resonators diverge from their ideal behavior due to spurious modes that cause high loss regions throughout their operating frequency range. Typically, control of piezoelectric resonator DC-DC converters is constrained to unidirectional power flow each resonant cycle for maximum efficiency operation. However, output power depends on the frequency with such control, which means the converter cannot operate at loads corresponding to spurious mode frequencies. This paper presents a fixed-frequency control mode utilizing the high-quality factor of piezoelectric resonators to avoid spurious modes. The fixed-frequency control enables efficient operation spanning the converter's full load range, demonstrated through a prototype DC-DC converter with a custom fabricated lithium niobate resonator. At a conversion ratio of 60 V to 30 V, spurious modes limit the converter's operating range from 33 W to 51 W using unidirectional power-constrained control, yet the fixed-frequency control extends operation from 33 W to 2 W.
7 August 2023 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
Piezoelectric power converters, where acoustic resonators replace the inductors as energy storage elements, promise much higher power density and higher efficiency compared to conventional circuits. Recently, lithium niobate (LiNbO 3 ) piezoelectric resonators have been integrated within power converter circuits, showing good conversion efficiency, thanks to their high quality factor ( Q ) and electromechanical coupling ( kt2 ). However, the converter output power range is limited by large spurious modes near resonance. This work reports a near-spurious-free LiNbO 3 thickness shear (TS) resonator, demonstrating high Q of 3500 and kt2 of 45% at 5.94 MHz, with a fractional suppressed region of 35%. First, we identify the best LiNbO 3 crystal orientation for efficient TS resonators. Then, we propose a novel acoustic design without busbars for spurious suppression, which is extensively simulated, fabricated, and characterized. Further analysis is done to identify existing spurious modes in our proposed design, specifically the effect of dicing on our TS resonator design. Upon optimization, LiNbO 3 TS resonators could potentially empower a new design space for low-loss and compact power converters.
19 May 2025 in IEEE Transactions on Power Electronics
Theoretically, increasing dc–dc converter switching frequency enables smaller passive components and high system power density, as required by many applications. However, inductors and transformers intrinsically scale poorly to high frequency and small volumes, creating a bottleneck to realizing high frequency, high power density dc–dc converters. Designing dc–dc converters without inductors, and instead using piezoelectric resonators for passive energy storage, bypasses this bottleneck. While prototype piezoelectric resonator based dc–dc converters have demonstrated high power density and efficiency at MHz switching frequencies, these converters rely on open-loop control. Practical applications necessitate closed-loop control for these converters, but the present methods for closed-loop control do not scale to MHz frequencies. This article presents a closed-loop control method for piezoelectric resonator based dc–dc converters using current mode control, feedforward compensation, and real-time calculated switch timings. The method scales to MHz switching frequency and is demonstrated with a 750 kHz, 100 W, 99.3% efficient prototype converter using paralleled, radial mode lithium niobate resonators.
12 February 2024 in IEEE Open Journal of Power Electronics
Piezoelectric resonators promise to increase dc-dc converter power density by replacing inductive components. However, piezoelectric resonators are not direct circuit level replacements for inductors, requiring new topologies. In this paper, we present a stacked converter using two piezoelectric resonators, providing improved efficiency at low conversion ratios. This converter is realized with a lithium niobate thickness-shear mode resonator with interdigitated electrodes that allow the two resonators required for the topology to be realized as tightly matched sub-resonators on the same substrate. The 180 V to 60 V converter operates between 6.15 MHz and 6.35 MHz and achieves a resonator-level power density of $\rm {1.34}~\rm {kW}/\rm {cm}^{3}$ .
1 May 2025 in IEEE Transactions on Power Electronics
Efficient radio frequency (RF) power amplifiers (PAs) are essential in various industrial applications, where fast RF pulses are often required to enhance system performance. In this article, we present a novel approach to fast RF power modulation using a resistance regulation network (RRN) with frequency adjustment. The proposed method is complementary to existing systems and can be adapted to a wide range of power and frequency levels. To illustrate the general design methodology of the RRN, we use an inductively coupled, double-tuned network as an example. We also discuss its loading effects and provide design guidelines for broadband switched-mode PAs. A 300 W class-$\Phi _{2}$ amplifier with RRN is implemented and tested, achieving a peak efficiency of 94%. Operating between 13.2 and 14.4 MHz, the amplifier is capable of doubling its output power within 500 ns while maintaining zero-voltage-switching (ZVS).