A scheme for conditional generating Hermite polynomial excited squeezed vacuum states (HPESVS) is proposed. Injecting a two-mode squeezed vacuum state (TMSVS) into a beam splitter (BS) and counting the photons in one of the output channels, the conditional state in the other output channel is just a HPESVS. To exhibit a number of nonclassical effects and non-Gaussianity, we mainly investigate the photon number distribution, sub-Poissonian distribution, quadrature component distribution, and Wigner function of the conditional HPESVS. We find that its nonclassicality closely relates to the control parameter of the BS, the squeezed parameter of TMSVS, and the photon number of conditional measurement. These further demonstrate that performing the conditional measurement on a BS is an effective approach to generate non-Gaussian state.
31 May 2016 in Journal of the Optical Society of America B
We theoretically generate nonclassical states from a coherent state heralded by Knill–Laflamme–Milburn (KLM)-type interference. Injecting a coherent state in signal mode and two single-photon sources in the other two auxiliary modes of KLM-type interferometry, a broad class of useful nonclassical states is obtained in the output signal port after making two single-photon-counting measurements in the two output auxiliary modes. The nonclassical properties, in terms of the antibunching effect and the squeezing effect as well as the negativity of the Wigner function, are studied in detail by adjusting the interaction parameters. The results show that the input coherent state can be transformed into non-Gaussian states with higher nonclassicality after measurement induction. The maximum squeezing of our generated states is about 1.97928 dB.
One- and two-mode successively squeezed state, obtained through re-squeezing two single mode squeezed states by the two-mode squeezing operator, is studied in terms of the technique of integration within an ordered product (IWOP) of operators. We first derive the normally ordered form of this one- and two-mode successively squeezing operator, and then investigate the quantum statistical properties of the corresponding squeezed state. Particularly, we use the Weyl ordering invariance under a similar transformation to derive the analytical expression of its Wigner function, which seems very easy and concise. Finally, the experimental generation of one- and two-mode successively squeezed state is also proposed simply.
In TiO2-based perovskite solar cells (PSC), the preparation of the CH3NH3PbI3/TiO2 composite layer is very important, since the morphology of the perovskite adsorbed onto the surface of the TiO2 nanoparticles has decisive significance for the absorption of the incident sunlight and separation of the generated carrier. The traditional two-step spin-coating method for the deposition of CH3NH3PbI3 into the porous mesoporous TiO2 layer usually suffers from filling block problems. In this study, the PbO-TiO2 mesoporous layer was prepared with various ratios of Pb:Ti in the raw materials. Morphological, optical, and element analysis of the prepared thin films indicated that Pb was gradually mixed into the TiO2 mesoporous layer with the increased Pb:Ti ratios. The element distribution characteristics of the optimal thin films showed that the distribution of Pb was uniform throughout the whole TiO2 thin film, which indicates the successful mixing of Pb into the TiO2 electrode layer. Combined with dip coating, the PbO-TiO2 mesoporous layer was prepared into a CH3NH3PbI3/TiO2 composite layer and subsequently to a solar cell device. The prepared solar cell shows a short-circuit photocurrent density of 16.4 mA/cm2, an open-circuit voltage of 900 mV, a fill factor of 61%, and a power conversion efficiency (PCE) of 9.00%. The PCE of the PSC is promoted by nearly 25% when compared with that prepared with the traditional method. The proposed preparation method that combines TiO2 nanoparticle electrode with a mixing and dip coating provides a new effective way to improve the deposition of perovskite into the mesoporous TiO2 layer, which is very helpful for the fabrication of high-efficiency and low-cost PSC.
29 December 2011 in International Journal of Quantum Chemistry