16 December 2022 in Journal of Materials Engineering and Performance
This study examines the abrasive wear behavior of nano-sized steel scale on the CuZn35Ni2 Soft material. CuZn35Ni2 Soft material was used as a sample, and the three-body wear mechanism formed by nanoscale particles mixed with lubricating oil was investigated using a ball-on-flat tester. Three different loads, three different sliding speeds and three different environment variables were used in the experiments. A lubricant containing 0.15 and 0.3 wt.% nanoscale and a non-abrasive lubricant was used to form the medium. The experimental results were obtained as mass loss, wear depth and friction coefficient and the wear surfaces were examined using scanning electron microscopy/energy-dispersive x-ray spectroscopy (SEM/EDX). The analysis of variance method was used to determine the effect of independent variables on the results. As a result of the study, it was concluded that the most effective parameter for mass loss and CoF was the environment, and the most effective parameter for the depth of wear was the load. It was concluded that there might be a difference of up to 10% in the coefficient of friction between the experiments and the predicted values. Still, in general, the predicted values and the experimental results agree.
1 January 2021 in Scientific Journal of Silesian University of Technology. Series Transport
During a study of the combustion process of a direct polarity electric arc, a directly proportional dependence of the electric current value on the degree of cold plastic deformation of carbon steel used as an electrode was found. To calculate the value of the electric current during arc burning, in the indicated ratio, it was proposed to replace the surface tension force of the liquid metal with the surface tension of ferrite of plastically deformed carbon steel. Calculation of the ferrite's surface tension value on the deformation degree of the steel under study through the size of the coherent scattering regions was used to explain the observed dependence of the electric current during arc burning. From the analysis of the considered correlation ratios, it was found that with an increase in the cold deformation degree, the refinement of the coherent scattering regions results in the ferrite's surface tension increase and consequently, to an increase in the electric current during arc burning. Comparative analysis of the obtained results of calculating the value of electric current during arc burning through the surface tension of ferrite of cold-deformed carbon steel showed a fairly good coincidence with experimental data. The differences did not exceed 9%.
30 April 2023 in İmalat Teknolojileri ve Uygulamaları
In today's technology, the power of mechanization has emerged in places where manpower is insufficient in order to meet the increasing needs at many facilities. With belt conveyor systems, it has become much easier to transport the material from one site to another in the facilities in terms of time, distance, and capacity. Since belt conveyors are a reliable and cost-effective system in material handling, the quality of the belt used should be carefully determined. It is important that the wear and tear that occurs on the belt over time is repaired quickly and effectively in order not to prolong the downtime in the plant. A small damage detected needs to be repaired immediately so that it does not cause bigger problems. In this study, vulcanization time, which is one of the parameters affecting the belt strength in belt splice made by vulcanization method, is discussed. By studying the effect of time on belt strength, it is aimed to extend the life of the belt splicing area. According to the test results, it has been observed that the increase in vulcanization time has a positive effect on the tape strength and the usage of welding machine saves time in terms of faster use of the tape in the facility.
2 April 2026 in Arabian Journal for Science and Engineering
Wear is a significant surface deformation, particularly resulting from friction between contact surfaces in relative motion, and is frequently observed in engineering applications. The resulting wear shortens component life, reduces system efficiency, and leads to energy losses and increased costs. In this study, the wear performance of AA7075/SiC metal matrix composite was evaluated using a ball-on-flat abrasive wear test setup. Experiments were conducted at a constant sliding speed, at different applied load levels (10 N, 20 N, and 30 N), and under different environmental conditions (dry, MQL, and Nano-MQL). SEM was used to examine surface morphologies, a profilometer to determine wear track depths, EDX to detect material transfer, and a precision balance to measure weight losses. According to the results, wear increased with increasing applied load. However, wear was significantly reduced with Nano-MQL lubricant. The least amount of wear was obtained in the experiment conducted under Nano-MQL conditions with a 10 N load. The lubricant film layer formed on the material surface thanks to the Nano-MQL medium obtained using copper-based nanoparticles has increased wear resistance. These results show that nano-modified lubrication is a beneficial method for increasing the surface strength of AA7075/SiC composite.
15 April 2021 in Science and Transport Progress
Purpose. The aim of this work is to assess the effect of ferrite grain size of low-carbon steel on the development of strain hardening processes in the area of nucleation and propagation of deformation bands. Methodology. Low-carbon steels with a carbon content of 0.06–0.1% C in various structural states were used as the material for study. The sample for the study was a wire with a diameter of 1mm. The structural studies of the metal were carried out using an Epiquant light microscope. Ferrite grain size was determined using quantitative metallographic techniques. Different ferrite grain size was obtained as a result of combination of thermal and termo mechanical treatment. Vary by heating temperature and the cooling rate, using cold plastic deformation and subsequent annealing, made it possible to change the ferrite grain size at the level of two orders of magnitude. Deformation curves were obtained during stretching the samples on the Instron testing machine. Findings. Based on the analysis of stretching curves of low-carbon steels with different ferrite grain sizes, it has been established that the initiation and propagation of plastic deformation in the jerky flow area is accompanied by the development of strain hardening processes. The study of the nature of increase at dislocation density depending on ferrite grain size of low-carbon steel, starting from the moment of initiation of plastic deformation, confirmed the existence of relationship between the development of strain hardening at the area of jerky flow and the area of parabolic hardening curve. Originality. One of the reasons for decrease in Luders deformation with an increase of ferrite grain size of low-carbon steel is an increase in strain hardening indicator, which accelerates decomposition of uniform dislocations distribution in the front of deformation band. The flow stress during initiation of plastic deformation is determined by the additive contribution from the frictional stress of the crystal lattices, the state of ferrite grain boundaries, and the density of mobile dislocations. It was found that the size of dislocation cell increases in proportion to the diameter of ferrite grain, which facilitates the development of dislocation annihilation during plastic deformation. Practical value. Explanation of qualitative dependence of the influence of ferrite grain size of a low-carbon steel on the strain hardening degree and the magnitude of Luders deformation will make it possible to determine the optimal structural state of steels subjected to cold plastic deformation.
26 June 2024 in Journal of Materials and Mechatronics: A
In In this work, the three-body abrasive wear of bronze (C86200) in pig cart transmissions was examined. Micro-nano-sized ore particles were introduced to the lubricating media during the Ball-on-flat test to represent three-body abrasive wear. Load shear rate and lubricating medium were useful research inputs. Outputs included examining sample surfaces, mass loss, friction coefficient, and trace depth. Taguchi, ANOVA, and RSM were used to analyze experimental data. The most effective parameter for all outputs was the load value, with a rate of 55.76 percent, while the speed had the lowest influence on mass loss, at 9.74 percent. The regression model fits these results well.