24 September 2015 in International Journal of Pavement Engineering
Two traffic speed deflection devices (TSDDs) that measure surface deflections at posted traffic speeds (up to 80–96 kph) were evaluated through a recent Federal Highway Administration project that included field trials at the MnROAD facility. Four geophones were embedded near the pavement surface to measure surface deflections during field trials at each of three MnROAD cells. In addition, the MnROAD facility counted with numerous other sensors such as strain gauges to measure pavement responses and thermocouple trees to collect pavement temperature at various depths. For the implementation of TSDDs in any network-level pavement management system, it is important to utilise a proper analytical model that can accommodate moving load and viscoelastic properties of pavement layers in the simulation of TSDD measurements. The 3D-Move software was chosen for this purpose. The viscoelastic properties used for the asphalt concrete (AC) layer include dynamic modulus and damping coefficient as a function of frequency relevant to the temperature at the time of the MnROAD field trials. The field trials and available data represented realistic field case scenarios to validate once more 3D-Move specifically for TSDD measurements. The proposed dynamic analytical model provided a good match with a variety of independent pavement responses that included surface deflection bowls (measured using embedded geophone sensors) as well as horizontal strains at the bottom of the AC layers (measured using MnROAD sensors).
1 January 2012 in Transportation Research Record: Journal of the Transportation Research Board
Ride quality and structural adequacy are key pavement performance indicators. The relationship between these indicators has been a topic of frequent and continuing discussion in the pavement community, but an accepted and widely used relationship has not yet been identified. The objective of this study was to identify and verify the relationship between these two performance indicators, if any, with data from the Long-Term Pavement Performance Program. This study was meant to improve the evaluation and use of pavement condition data in pavement rehabilitation and design decisions. More specifically, it was intended to develop and document a mechanism to include values of both ride and structural adequacy within the context of current network-level pavement management system practices for highway agency implementation to ensure smooth pavements that are also structurally adequate. To accomplish the study objective, two major activities were carried out: a literature search to gather, review, and synthesize available information on relating ride quality and structural adequacy and a review and assessment of data from the Long-Term Pavement Performance Program to determine if such a relationship exists. These two activities—as well as their major findings, observations, and conclusions—are detailed; a viable relationship could not be identified.
1 September 1990 in Journal of Transportation Engineering
Several methods for designing concrete block pavements (CBP) for roads and streets are presently available. All recognize the need to consider the subgrade soil, paving materials, environment, and anticipated traffic. There are a number of limitations associated with each, including inadequate characterization of the subgrade soil and paving materials, lack of pavement performance prediction capabilities, and inability to specify desired pavement failure and reliability level. This paper presents a method to overcome these limitations. The AASHTO flexible pavement design methodology is used as the fundamental framework for developing this procedure. Several modifications allow for the characterization of concrete block pavers, as well as for various levels of engineering analysis, depending on the availability of information. The proposed design methodology is demonstrated through a numerical example.
1 January 1997 in Transportation Research Record: Journal of the Transportation Research Board
The use of manual survey methods within the Long-Term Pavement Performance (LTPP) program for the collection of distress data has drastically increased both in intensity and in coverage over the past couple of years. Because these surveys are conducted by individual raters whose biases can lead to variability between raters, it was hypothesized that distress data variability existed and that it could potentially be quite large. Thus, the purpose of the presented study was to quantify manual distress data variability, with special emphasis on the bias and precision of the data. Results from seven LTPP program distress rater accreditation workshops conducted during the period from 1992 to 1995 were used as the only source of data. On the basis of analyses of these data, both the apparent bias and the precision for the common distress type-severity level combinations were quantified. It was also concluded from this study that individual rater variability for any given distress type-severity level combination is typically large and increases as the distress quantity increases; however, when all distress type-severity level combinations are viewed in terms of a single composite number such as the pavement condition index value, there is excellent agreement between the individual raters, the group mean, and the ground truth value, and individual rater variability is also quite small. Because LTPP program distress data are to be used in the development of pavement performance prediction models, improvements in variability are highly desirable to ensure that they serve their intended purpose. Recognizing that the LTPP program distress raters are experienced individuals, such improvements are not envisioned to come through additional training. It is the authors’ contention that the only way of achieving the desired improvement is through the conduct of group consensus surveys.
1 January 1997 in Transportation Research Record: Journal of the Transportation Research Board
The interpretation and use of deflection measurements on the prepared surfaces of the various pavement layers during construction are examined. Measurements were obtained from four asphalt concrete pavement test sections, two with unbound aggregate base and two with bituminous-treated base over an untreated aggregate base. Deflection basin measurements using a falling weight deflectometer were performed on the prepared surfaces of the subgrade, base layers, and asphalt concrete layers. The elastic moduli of each layer were computed using the EVERCALC backcalculation program. The primary finding from this investigation is that deflection measurements on the subgrade and base layers during construction can be used to control construction uniformity and provide checks on mechanistic-based pavement design assumptions. Also, subgrade uniformity has a profound impact on the entire pavement structure and subgrade variations affect total deflections and computed layer moduli of all successive layers. The backcalculated modulus is directly related to the stress state in the layer. For unbound aggregate bases, the backcalculated elastic modulus decreases with a decrease in the bulk stress, and for fine-grained subgrade soil, the backcalculated elastic modulus increased with a decrease in the deviator stress. As expected, a higher and more variable root-mean-square basin fit error value was obtained for measurements on unbound material as compared with measurements on bound material surfaces.