A peel-off mask is a type of dosage form that is gently applied onto the skin and peeled off after a few minutes. It is one of the most popular skincare products used to treat facial-related conditions. This study is aimed at designing and optimizing a peel-off facial mask formulation containing 20% w/w of soybean extract by response surface methodology (RSM). The peel-off mask was formulated using different concentrations of polyvinyl alcohol (PVA), ethanol, and carbomer 940. The isoflavonoids content of the soybean extract was determined using spectrophotometric method. Physicochemical properties (homogeneity, colour, odour, and pH) of the peel-off mask formulation were examined. Other parameters investigated include drying time, applicability, film-forming performance, and loading efficiency. The stability of the formulation was also investigated. The results showed that the PVA and ethanol concentrations significantly affected the drying time of the formulation. The PVA concentration and its quadratic term significantly influenced applicability of the formulation. The amount of carbomer in the formulation had the most significant impact on how well the film formed. The optimized formulation is composed of 20% soybean extract, 12.03% PVA, 8.36% ethanol, and 0.52% carbomer. Stability test results show that low temperature (5 ± 1°C) and room temperature, protected from sunlight (22 ± 2°C) have no effect on the stability of the formulation, and that phenoxyethanol at 1.0% w/w could preserve the formulation from microbial degradation undervarious storage conditions. Therefore, RSM was a helpful way to figure out the best conditions for making soybean peel-off facial masks.
28 February 2023 in Drug development & registration
Introduction. As the first approved drug for amyotrophic lateral sclerosis (ALS) treatment, riluzole is known as a glutamatergic neurotransmission inhibitor administrated in 50 mg tablets twice daily. For this reason, a generic product of riluzole has been developed at a lower price by Hogar-Daroo, Iran, which would benefit patients.Aim. The objective of this study is to develop and validate a novel liquid chromatography-tandem mass spectrometry (LC-MS/MS) method for the analysis of riluzole in human plasma samples and its application in the bioequivalence study of riluzole tablet.Materials and methods. The chromatography was performed by using a C18 column (100 mm, 4.6 mm, 5 mm), 0.1 % formic acid and acetonitrile (60 : 40, v/v) as the mobile phase, at a flow rate of 0.90 ml/min in the gradient program. Carbamazepine was used as an internal standard (IS). The method employed only 100 µL of human plasma for quantification by a liquid-liquid extraction technique. The multiple reaction monitoring modes (MRM) was used for quantification of ion transitions m/z 235.0/165.9 and m/z 137.6/110.0 for riluzole and the m/z 236.9/194.0 for the IS. Dwell time was set at 200 ms.Results and discussion. The calibration curve was linear over the concentration range 0.5–300 ng/mL. The lower limit of quantitation (LLOQ) was obtained at 0.5 ng/mL. The intra-day and inter-day accuracy ranged from 93.21 % to 101.34 % and 91.77 % to 104.88 % respectively. The intra-day and inter-day precision values ranged from 2.19 % to 5.69 % and 1.67 % to 5.31 % respectively, all within the FDA acceptable ±15 %.Conclusion. The validated method was applied in Iranian healthy subjects under fasting condition with a 50 mg riluzole tablet successfully.
30 June 2026 in Journal of Dental Research, Dental Clinics, Dental Prospects
Introduction: White spot lesions (WSLs) are early indicators of enamel demineralization and require effective r e m i n e r a l i z a t i o n strategies to prevent progression. This in vitro study aimed to prepare and evaluate a dental varnish containing casein phosphopeptide-amorphous calcium phosphate with fluoride (CPP-ACPF) and to compare its remineralization efficacy with a commercial MI GC varnish and a control varnish. Methods: The dental varnish formulation was prepared. To evaluate its physicochemical properties and compare them with the MI varnish, density and viscosity measurements were conducted. To evaluate the effect of the varnishes on remineralization, 36 enamel specimens were obtained from the buccal surface of extracted human non-carious premolars. The specimens were randomly divided into three groups (n=12). Microhardness measurements of the tooth surface were taken at three stages: (1) baseline (sound enamel) before demineralization, (2) immediately after demineralization, and (3) after the remineralization period. Scanning electron microscopy (SEM) was used to examine the enamel surface morphology at each stage. Results: Enamel surface microhardness (Vickers hardness number, VHN) significantly decreased after demineralization (baseline: 310±12; after demineralization: 185±10; P<0.001). Following treatment, the prepared CPP-ACPF group exhibited the highest recovery (275±11 VHN), compared with MI varnish (245±13 VHN) and control (210±9 VHN). Repeated-measures mixed ANOVA confirmed significant differences between the groups (PMI varnish>control. Scanning electron microscopy revealed smoother and more uniform remineralized surfaces in the prepared CPP-ACPF group. Conclusion: The results indicated that the prepared CPP-ACPF varnish provided superior remineralization and could serve as a stable, cost-effective option for managing early enamel lesions.