Angélica Daiane Schneider

Angélica Daiane Schneider

Auto-generated profile, based on publicly available information

Angélica Daiane Schneider

Postgraduate Program in Physics (PGFisica), Department of Physics, Federal University of Santa Maria, Santa Maria, Brazil

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 March 2026 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
Rafael Luciano DalcinRafael Luciano Dalcin
Rafael Luciano Dalcin
SHSamara Herrmann
Samara Herrmann
DLDalton Daniel de Lima
Dalton Daniel de Lima
ASAngélica Daiane Schneider
Angélica Daiane Schneider
BSBruna Karine dos Santos
Bruna Karine dos Santos
CSCristiano José Scheuer
Cristiano José Scheuer

1 January 2024 in Materials Research
Verified
Journal Article
Open access
PDF file
DSD. M. C. dos Santos
D. M. C. dos Santos
FSF. Signor
F. Signor
ASA.D. Schneider
A.D. Schneider
CBCaroline Raquel Bender
Caroline Raquel Bender
PMP. H. Mareze
P. H. Mareze
NDN.F. Daudt
N.F. Daudt
Powder metallurgy is an attractive method for cost effective production of near net shape Ti-Nb alloys, and, when elemental powders and coarse HDH powders are used, a higher flexibility in alloy composition and low processing costs can be achieved. In this study, manufacturing of (α+β) Ti-Nb alloys by powder metallurgical techniques using coarse HDH Nb (D50= 110 μm and D50= 255 μm) and HDH Ti (D50= 22.6 μm) powders as starting materials was described. Tape casting was applied for the production of porous sheets while warm compaction of Metal Injection Molding (MIM) feedstock was applied for the production of dense parts. Microstructural and mechanical tests were employed to investigated the effect of coarse Nb powders on the sintering behavior and mechanical properties. Tape casting enabled to produce porous sheets of Ti16Nb alloy with an interconnected porosity varying from 14 - 31 vol.%. Warm compaction enabled to produce Ti-Nb parts with less than 2% porosity and Yield strength in compression of 975-1100 MPa, which is similar to the values reported for Ti-Nb based alloys produced by powder metallurgy of finer powders. A dynamic Young’s Modulus of 37-52 GPa, significantly lower than that of cp-Ti was achieved. These results might provide guidelines for the use of coarse Nb powders as starting materials for the powder metallurgical development of low-cost Ti-Nb based alloys.

27 October 2025 in Thin Solid Films
Verified
Journal Article
Closed access
ASA.D. Schneider
A.D. Schneider
PBP.S. Boeck
P.S. Boeck
GCG. Copetti
G. Copetti
TMThiago Mori
Thiago Mori
RPR.D. Della Pace
R.D. Della Pace
Lucio Strazzabosco DornelesLucio Strazzabosco Dorneles
Lucio Strazzabosco Dorneles

24 July 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
ASAngélica Daiane Schneider
Angélica Daiane Schneider
GAGwenaël Atcheson
Gwenaël Atcheson
LSLuis Fernando Schelp
Luis Fernando Schelp
PSPlamen Stamenov
Plamen Stamenov
Lucio Strazzabosco DornelesLucio Strazzabosco Dorneles
Lucio Strazzabosco Dorneles
Vanadium dioxide is a fascinating material whose physical properties change abruptly just above room temperature. Here we investigate vanadium dioxide thin films produced by reactive magnetron sputtering. Key factors, that interfere directly in the vanadium dioxide production using reactive magnetron sputtering, were investigated. Two main parameters are found to be crucial in reproducibility at large scale: purity of the target and oxygen consumption. Two additional procedures can be added to traditional reactive magnetron sputtering in order to identify the proper deposition parameters: monitor the oxygen partial pressure, and analyze the power source voltage applied to the target.

19 June 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
ASAngélica Daiane Schneider
Angélica Daiane Schneider
VEV.M. Escobar
V.M. Escobar
GCG.L. Callegari
G.L. Callegari
MGM. Gamino
M. Gamino
TMThiago Mori
Thiago Mori
LSLuis Fernando Schelp
Luis Fernando Schelp
Three samples of vanadium dioxide thin films with different crystallographic structures at room temperature, P21/c (M1), P1 (T), and a mixture of both (M1-T), were analyzed. Atomic force microscopy images obtained at room temperature show clearly that the thin films are composed of percolated nanocrystals. X-ray diffraction experiments using 7 keV synchrotron radiation were performed before and after the crystallographic transition to the rutile (R) phase, and the Williamson-Hall method was used to separate contributions from strain and from crystallite size. The presence of the strain in the R phase induces transition to the T phase as the temperature decreases through the transition. Williamson-Hall plots can also be used to obtain relative strain values from polycrystalline samples.

13 March 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
ASAngélica Daiane Schneider
Angélica Daiane Schneider
GAGwenaël Atcheson
Gwenaël Atcheson
LSLuis Fernando Schelp
Luis Fernando Schelp
PSPlamen Stamenov
Plamen Stamenov
Lucio Strazzabosco DornelesLucio Strazzabosco Dorneles
Lucio Strazzabosco Dorneles
Vanadium dioxide is a fascinating material whose physical properties change abruptly just above room temperature. Here we investigate vanadium dioxide thin films produced by reactive magnetron sputtering. Key factors, that interfere directly in the vanadium dioxide production using reactive magnetron sputtering, were investigated. Two main parameters are found to be crucial in reproducibility at large scale: purity of the target and oxygen consumption. Two additional procedures can be added to traditional reactive magnetron sputtering in order to identify the proper deposition parameters: monitor the oxygen partial pressure, and analyze the power source voltage applied to the target.