Alain Giani

Alain Giani

Auto-generated profile, based on publicly available information

Alain Giani

IES, Université de Montpellier, Montpellier, France

Research Focus & Metrics

Academic Career Length

34Years (1993-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 April 2011 in Journal of Materials Science: Materials in Electronics
Verified
Journal Article
Closed access
PDF file
BCBenoit Charlot
Benoit Charlot
SGSebastian Gauthier
Sebastian Gauthier
AGAlexandra Garraud
Alexandra Garraud
PCPhilippe Combette
Philippe Combette
AGAlain Giani
Alain Giani

1 April 2022 in AIAA Journal
Verified
Journal Article
Closed access
JWJulien Weiss
Julien Weiss
BSBen Steinfurth
Ben Steinfurth
LCLéo Chamard
Léo Chamard
AGAlain Giani
Alain Giani
PCPhilippe Combette
Philippe Combette
Spectral proper orthogonal decomposition (SPOD) is used to investigate the low-frequency behavior of a pressure-induced turbulent separation bubble (TSB) generated on a one-sided diffuser at a nominal velocity of 20 m/s. The input to the decomposition is the unsteady wall shear stress determined experimentally with an array of novel calorimetric shear-stress sensors. The SPOD spectrum indicates low-rank behavior for frequencies below 10 Hz, which correspond to Strouhal numbers [ ] when built with the average TSB length and the nominal incoming velocity. A low-order model constructed with only the first SPOD mode at each frequency up to 10 Hz reveals that the TSB is contracting and expanding in a manner reminiscent of the low-frequency breathing motion recently documented in other TSBs. A comparison between SPOD and space-only proper orthogonal decomposition (POD) indicates that both decompositions are able to capture the low-frequency breathing motion as long as space-only POD is applied on signals previously low-pass filtered at 10 Hz. However, the superiority of SPOD is revealed by its inherent capacity to express the frequency range amenable to low-rank behavior. In addition to offering new insights into the low-frequency dynamics of TSBs, the present results also demonstrate the usefulness of calorimetric shear-stress sensors for the study of turbulent separating and reattaching flows.

30 November 2012 in Micro & Nano Letters
Verified
Journal Article
Closed access
AGAlexandra Garraud
Alexandra Garraud
PCPhilippe Combette
Philippe Combette
ADA. Deblonde
A. Deblonde
PLPatrice Loisel
Patrice Loisel
AGA. Giani
A. Giani
A significant improvement of thermal accelerometer bandwidth κ demonstrated. In a classic open-loop configuration, a micromachined thermal accelerometer having a width of 1500 µm has a sensitivity of 0.045°C/g and a bandwidth up to 66 Hz limited by gas thermal response. A new sensor architecture is proposed to improve bandwidth with no sensitivity decrease: a closed-loop configuration with the addition of two resistors placed close to detectors to rebalance their temperature. They directly act on the thermal response of the fluid. Thus, sensor bandwidth is increased up to 1 kHz with a similar sensitivity of 0.034°C/g.

19 October 2022 in Sensors and Actuators A: Physical
Verified
Journal Article
Closed access
JGJulian Giehler
Julian Giehler
LCLéo Chamard
Léo Chamard
CECarola Ebert
Carola Ebert
JWJulien Weiss
Julien Weiss
AGAlain Giani
Alain Giani
PCPhilippe Combette
Philippe Combette

1 November 2023 in IEEE Sensors Journal
Verified
Journal Article
Closed access
LCLéo Chamard
Léo Chamard
JGJulian Giehler
Julian Giehler
JWJulien Weiss
Julien Weiss
PCPhilippe Combette
Philippe Combette
AGAlain Giani
Alain Giani
A family of calorimetric wall shear stress microsensors is investigated numerically and experimentally to determine their static response curves and their capacity to detect reattachment in a turbulent separated air flow. Four sensor designs are considered: a “Gap” design that features three separated beams suspended over a cavity, a “NoGap” design where the three beams are mechanically connected for enhanced robustness, a “Membrane” design where the cavity is closed, and finally a “Kapton” design without any cavity. The results show that connecting the beams by either removing the gap, adding a membrane, or getting rid of the cavity altogether, lowers the sensor’s sensitivity. This is explained by the enhanced conductive heat transfer between the beams. Furthermore, while all designs can detect the average reattachment line in a turbulent flow, only the sensors featuring a cavity are sensitive enough to accurately measure the small-scale regions of backflow characterizing turbulent separated flows. These findings will help the design of both robust and sensitive calorimetric shear-stress sensors for aerodynamic applications.

1 September 2002 in Journal of Crystal Growth
Verified
Journal Article
Closed access
ABA. Al Bayaz
A. Al Bayaz
AGA. Giani
A. Giani
AFA. Foucaran
A. Foucaran
FPF. Pascal-Delannoy
F. Pascal-Delannoy
ABA. Boyer
A. Boyer