CaCO3 is often used as an additive in many industries. However, additional functions are required to expand its applicability. This entails modification of its physicochemical properties. Accordingly, in this study, a particle surface modification treatment was performed on CaCO3 produced from desulfurized gypsum for a range of industrial applications. In the experiment, fatty acids were used to modify the CaCO3 surface, and the scale of the modification effect was based on the degree of change associated with a polar surface taking on nonpolar surface properties. In the preliminary modification experiment, stearic acid was dissolved in 2-propanol or chloroform, and the extent of the reaction and the active ratio were measured according to the stearic acid concentration. The results showed that the effective active ratio, considering the activity to unit adsorption, was higher in 2-propanol than in chloroform. Consequently, the modification solvent used in the experiment changed the CaCO3 surface from a hydrophilic, polarized form to a hydrophobic, nonpolarized form. These results will also allow the CaCO3 produced to be used as a filler in a range of chemical industries.
Blast furnace slag (BFS) was selected as the source of Ca for CO2 mineralization purposes to store CO2 as CaCO3. BFS was dissolved using aqua regia (AR) for leaching metal ions for CO2 mineralization and rejecting metal ions that were not useful to obtain pure CaCO3 (as confirmed by XRD analysis). The AR concentration, as well as the weight of BFS in an AR solution, was varied. Increasing the AR concentration resulted in increased metal ion leaching efficiencies. An optimum concentration of 20% AR was required for completely leaching Ca and Mg for a chemical reaction with CO2 and for suppressing the leaching of impurities for the production of high-purity carbonate minerals. Increasing the liquid-to-solid ratio (L/S) resulted in the increased leaching of all metal ions. An optimum L/S of 0.3/0.03 (=10) was required for completely leaching alkaline-earth metal ions for CO2 mineralization and for retaining other metal ions in the filtered residue. Moreover, the filtrate obtained using 20% AR and an L/S of 0.3/0.03 was utilized as Ca sources for forming carbonate minerals by CO2 mineralization, affording CaCO3. The results obtained herein demonstrated the feasibility of the use of AR, as well as increasing pH, for the storage of CO2 as high-purity CaCO3.
The effects of CO2 flow rate and calcium source on the particle size (PS) and specific surface area (SSA) of CaCO3 particles were evaluated using microbubble generator (MBG) and air diffuser (AD) systems. The carbonate mineralization (CM) and precipitated calcium carbonate (PCC) methods were employed to produce CaCO3 using gypsum and Ca(OH)2 as the calcium sources, respectively. The CaCO3 particles prepared using the MBG were smaller (with larger specific surface area) than those obtained using the conventional AD, regardless of the calcium source. The average PSs were 2–3 and 7–9 μm for the MBG and AD systems, respectively. Moreover, the PS and SSA of the particles prepared using the MBG were not greatly affected by the CO2 injection rate. This study clearly demonstrates that the use of an MBG ensures the stable production of fine CaCO3 particles using various calcium sources and a wider range of CO2 flow rates.
Blast furnace slag (BFS), a calcium-rich industrial byproduct, has been utilized since 2005 as a mineral carbonation feedstock for CO2 sequestration, producing calcium carbonate precipitates. In this study, the conditions for the dissolution of Ca and Si in acetic acid, and subsequent carbonation, were elaborated. For this purpose, the retardation of the polymerization of silicon was attempted by varying the concentration of acetic acid, temperature, and leaching time. An inductively coupled plasma (ICP) analysis revealed that both the Ca and Si dissolved completely within 30 min in 5% acetic acid at room temperature. This high dissolution value can be attributed to the fact that Ca was bound to O rather than to Si, as determined by X-ray photoelectron spectroscopy (XPS). The use of CO2-absorbed monoethanolamine enabled the complete carbonation of BFS at ambient conditions without the need for a pH swing. The presence of dissolved silica was found to affect the polymorphs of the precipitated CaCO3. We believe that this process offers a simple method for manipulating the composites of products obtained by mineral carbonation diminishing the leaching residues.
Carbon capture and storage is a popular CO2-reduction technology, and carbon capture and utilization (CCU) technology has been reported frequently over the years. However, CCU has certain disadvantages, including the requirement of high energy consumption processes such as mineral carbonation. In addition, stable metal sources are required to fix CO2. This study used concentrated seawater to supply metal ions. In addition, the selected 5 wt % amine solution changed CO2 into aqueous CO2 to reduce the additional energy required to form the metal carbonate under moderate conditions. As a result, precipitates were formed because of the reaction of carbonate radicals with metal ions in the seawater. These precipitates were analyzed by X-ray diffraction and field-emission scanning electron microscopy, and they were found to mostly consist of CaCO3 and NaCl. Furthermore, it was verified that the conversion solution maintained its CO2-loading capacity even after the solids and liquid were filtered twice. Therefore, the proposed method permits a substantial reuse of CO2 and waste seawater when sufficient metal ions are supplied. Therefore, methods to improve their purity will be developed in future studies.