Anne Straße

Anne Straße

Auto-generated profile, based on publicly available information

Anne Straße

Department 9.3-Welding Technology, Bundesanstalt für Materialforschung und-prüfung (BAM), Berlin, Germany

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 November 2020 in Quantitative InfraRed Thermography Journal
Verified
Journal Article
Open access
SASimon Altenburg
Simon Altenburg
ASAnne Straße
Anne Straße
AGAndrey Gumenyuk
Andrey Gumenyuk
Christiane MaierhoferChristiane Maierhofer
Christiane Maierhofer
Additive manufacturing offers a range of novel applications. However, the manufacturing process is complex and the production of almost defect-free parts with high reliability and durability is still a challenge. Thermography is a valuable tool for process surveillance, especially in metal additive manufacturing processes. The high process temperatures allow one to use cameras usually operating in the visible spectral range. Here, we compare the results of measurements during the manufacturing process of a commercial laser metal deposition setup using a mid wavelength infrared camera with those from a short wavelength infrared camera and those from a visual spectrum high-speed camera with band pass filter in the near infrared range.

1 January 2022 in Materials Testing
Verified
Journal Article
Closed access
GPGiuseppe Pignatelli
Giuseppe Pignatelli
ASAnne Strasse
Anne Strasse
AGAndrey Gumenyuk
Andrey Gumenyuk
IGIgor Gornushkin
Igor Gornushkin
Additive manufacturing by laser metal deposition (LMD) requires continuous online monitoring to ensure quality of printed parts. Optical emission spectroscopy (OES) is proposed for the online detection of printing defects by monitoring minute variations in the temperature of a printed spot during laser scan. A two-lens optical system is attached to a moving laser head and focused on a molten pool created on a substrate during LMD. The light emitted by the pool is collected by an ultraviolet–visible (UV–vis) spectrometer and processed. Two metrics are used to monitor variations in the surface temperature: the spectrally integrated emission intensity and correlation coefficient. The variations in the temperature are introduced by artificial defects, shallow grooves, and holes of various widths and diameters carved on a substrate surface. The metrics show sufficient sensitivity for revealing the surface defects, except for the smallest holes with an under-millimeter diameter. Additionally, numeric simulations are carried out for the detection of emission in the UV–vis and near-infrared (NIR) spectral ranges at various surface temperatures. It is concluded that both the metrics perform better in the NIR range. In general, this work demonstrates that spectrally resolved OES suits well for monitoring surface defects during 3D metal printing.

29 July 2023 in Welding in the World
Verified
Journal Article
Open access
PDF file
ASAnne Straße
Anne Straße
AGAndrey Gumenyuk
Andrey Gumenyuk
Michael RethmeierMichael Rethmeier
Michael Rethmeier
AISI 2205 duplex stainless steel is used in a variety of industries, including the chemical and petrochemical industries. This is due to its high tensile strength combined with good ductility and corrosion resistance. However, in laser beam welding, these properties are negatively affected by the high cooling rates typical of the welding process. The resulting higher ferrite content in the weld metal than in the base material leads to a reduction in the ductility and corrosion resistance of the welded joint. To overcome this problem, in this study, thick plates were coated by direct energy deposition (DED) prior to laser beam welding, whereas a duplex powder mixture containing a higher nickel concentration was used as a coating material. To improve the weld quality for the proposed two-step process, a method of additional material deposition instead of conventional tack weld was investigated. The resulting welded joints showed a well-balanced austenite to ferrite ratio and their properties and microstructure were verified by metallographic analysis, electron backscatter diffraction and Charpy impact testing. Using the standard ASTM G48 test method, it was found that the corrosion resistance of the welds was improved by a factor of four in average compared to the conventionally welded joints. The resulting properties, such as good ductility and corrosion resistance, of the welds with pre-coated edges showed good agreement with those of the base metal and confirmed the proposed two-step process as a promising alternative to the conventional approaches for welding thick duplex stainless steel plates.

25 February 2022 in Advanced Engineering Materials
Verified
Journal Article
Open access
ASAnne Straße
Anne Straße
AGAndrey Gumenyuk
Andrey Gumenyuk
MRMichael Rethmeier
Michael Rethmeier
Duplex stainless steels combine the positive properties of its two phases, austenite and ferrite. Due to its good corrosion resistance, high tensile strength, and good ductility, it has multiple applications. But laser beam welding of duplex steels changes the balanced phase distribution in favor of ferrite. This results in a higher vulnerability to corrosion and a lower ductility. Herein, different powder combinations consisting of duplex and nickel for coating layers by laser metal deposition (LMD) are investigated. Afterward, laser tracks are welded, and the temperature cycles are measured. The ferrite content of the tracks is analyzed by feritscope, metallographic analysis, and electron backscatter diffraction. The goal is the development of a powder mixture allowing for a duplex microstructure in a two‐step process, where first the edges of the weld partners are coated with the powder mixture by LMD and second those edges are laser beam welded. The powder mixture identified by the pretests is tested in the two‐step process and analyzed by metallographic analysis, energy‐dispersive X‐ray spectroscopy, and Vickers hardness tests. The resulting weld seams show a balanced duplex microstructure with a homogenous nickel distribution and a hardness of the weld seam similar to the base material.