Amine Charfi

Amine Charfi

Auto-generated profile, based on publicly available information

Amine Charfi

University of Sfax

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 September 2019 in Journal of Thermoplastic Composite Materials
Verified
Journal Article
Closed access
PDF file
ACAmine Charfi
Amine Charfi
SNSameh Neili
Sameh Neili
MKMohamed Kharrat
Mohamed Kharrat
MDMaher Dammak
Maher Dammak
This research article deals with commercial polytetrafluoroethylene (PTFE)-based composites filled with 30% of bronze microparticles. This shade is used as guide rings in hydraulic cylinders. After a certain number of slip cycles, seal wear is one of the main causes of leaks in the hydraulic systems. To solve this problem, it is essential to act on the seal materials to increase its lifetime and consequently the lifetime of hydraulic systems. Excessive pressure on the seal causes a significant wear while a light contact causes lubricant leak. For both situations, we have a failure of the system. For this reason, it is necessary to have a perfect contact between the seal and the metal surface and simultaneously with minimal wear. This problem is the subject of our research works. We analyze, in this article, the tribological behavior of a PTFE/bronze composite under dry and lubricated sliding conditions for different frequencies and loads. An alternating linear motion ball/plane tribometer has been used to characterize friction and wear behavior of the material. Micrographic observation of wear track was taken with the optical microscope. The results showed the good friction behavior of material for low values of loads and frequencies and essentially for 33 N of load with 1 Hz frequency or for 81 N as normal load with 0.75 Hz frequency as well as lubrication improve the wear rate of the PTFE/bronze composite. Under lubrication, load and frequency become inversely proportional to friction coefficients.

19 October 2022 in International Journal of Materials Research
Verified
Journal Article
Closed access
ACAmine Charfi
Amine Charfi
RARuttba Aziz
Ruttba Aziz
MKMohamed Kharrat
Mohamed Kharrat
MWMohd Farooq Wani
Mohd Farooq Wani
MDMaher Dammak
Maher Dammak
RSRakesh Sehgal
Rakesh Sehgal
Friction and wear behaviour of nano-sized silicon nitride in beta phase (β-Si3N4) under dry conditions were studied. Flat β-Si3N4 samples were prepared by means of the spark plasma sintering method. Sliding tests were performed using a reciprocating ball-on-flat tribometer against silicon carbide (SiC) ball and silicon nitride (Si3N4) ball under various normal loads. The frequency was set at 1 Hz and the sliding distance at 20 mm. The morphology of the worn surfaces was analysed by scanning electron microscopy. Experimental results showed that for normal load ranging from 11 to 57 N the friction coefficient increases from 0.15 to 0.36 for the β-Si3N4/SiC tribo-pair and from 0.8 to 0.9 for β-Si3N4/Si3N4 tribo-pair. Whereas, for both tribo-pairs, the specific wear rate decreases with the increase in normal load to reach an asymptotic minimum for high loads whose value is 0.15 × 10−3 mm3 N−1 m−1 for β-Si3N4/SiC and 0.3 × 10−3 mm3 N−1 m−1 for β-Si3N4/Si3N4. The experimental results show also that depending on the tribo-pair and normal load, soft and hard wear mechanisms are activated.

17 December 2025 in International Journal of Materials Research
Verified
Journal Article
Closed access
MZMontassar Zrida
Montassar Zrida
ACAmine Charfi
Amine Charfi
This study investigates the development of bio-composites reinforced with sheep wool fibers, aiming to valorize animal-based natural resources for sustainable material applications. Wool fibers were Soxhlet-treated to enhance compatibility with a polypropylene matrix, and composites were fabricated by heated platen pressing followed by injection molding, with fiber loadings ranging from 5 to 30 wt.%. Mechanical characterization revealed a strong reinforcing effect, with the Young’s modulus increasing from 1,000 MPa (neat polypropylene) to 2,720 MPa at 30 wt.% treated fibers (87 % improvement). This stiffness enhancement, however, was accompanied by reduced ductility (from 7.5 % to 1.55 %) and a moderate decrease in tensile strength (22 %). Morphological scanning electron microscopy and chemical Fourier transform infrared analyses confirmed improved but primarily physical interfacial adhesion, while thermogravimetric analysis indicated sufficient thermal stability for industrial processing. These findings highlight the potential of Soxhlet-treated wool fibers as reinforcement for polypropylene, enabling the design of scalable, eco-friendly composites for automotive, construction, and packaging applications.

5 August 2020
Verified
Book Chapter
Closed access
PDF file
ACAmine Charfi
Amine Charfi
IDIsmail Dhaou
Ismail Dhaou
MKMohamed Kharrat
Mohamed Kharrat
MWMohd Farooq Wani
Mohd Farooq Wani
MDMaher Dammak
Maher Dammak

27 April 2026 in Journal of Composite Materials
Verified
Journal Article
Closed access
ACAmine Charfi
Amine Charfi
Silicon nitride (Si 3 N 4 ) reinforced with molybdenum disilicide (MoSi 2 ) offers improved oxidation resistance and tribological stability compared to monolithic ceramics. This study presents comprehensive analytical modeling and validation of nano-sized Si 3 N 4 -MoSi 2 composite friction and wear behavior under reciprocating dry sliding against SiC counterface. Tribological testing was conducted at normal loads of 6–46 N and sliding frequencies 0.25–1.0 Hz, providing experimental database comprising friction coefficient evolution curves and specific wear rates. Novel analytical expressions incorporating sigmoidal and polynomial functions were developed and systematically validated to describe: friction coefficient evolution with cycle number at each load and frequency; steady-state friction dependence on normal load and frequency; and specific wear rate variation. Model fitting achieved R 2 > 0.95 for both transient and steady-state regimes, with normalized root-mean-square errors below 5%. The validated analytical framework captures quasi-linear load dependence and substantial frequency sensitivity (32% friction reduction from 0.25 to 1.0 Hz), while wear rate exhibits non-monotonic load dependence with minimum at approximately 30 N . Mechanistic analysis reveals that MoSi 2 functions as structurally compliant refractory phase facilitating mixed-oxide tribolayer formation. Compact design equations derived herein are directly implementable in component-level tribological simulations and bearing life prediction models.