Polymers have an excellent effect in terms of moderating fast neutrons with rich hydrogen and carbon, which plays an indispensable role in shielding devices. As the shielding of neutrons is typically accompanied by the generation of γ-rays, shielding materials are developed from monomers to multi-component composites, multi-layer structures, and even complex structures. In this paper, based on the typical multilayer structure, the integrated design of the shield component structure and the preparation and performance evaluation of the materials is carried out based on the design sample of the heat-resistant lightweight polymer-based interlayer. Through calculation, the component structure of the polymer-based materials and the three-layer thickness of the shield are obtained. The mass fraction of boron carbide accounts for 11% of the polymer-based material. Since the polymer-based material is the weak link of heat resistance of the multilayer shield, in terms of material selection and modification, the B4C/TiO2/polyimide molded plate was prepared by the hot-pressing method, and characterization analysis was conducted for its structure and properties. The results show that the ball milling method can mix the materials well and realize the uniform dispersion of B4C and TiO2 in the polyimide matrices. Boron carbide particles are evenly distributed in the material. Except for Ti, the other elemental content of the selected areas for mapping is in good agreement with the theoretical values of the elemental content of the system. The prepared B4C/TiO2/polyimide molded plate presents excellent thermal properties, and its glass transition temperature and initial thermal decomposition temperature are as high as 363.6 °C and 572.8 °C, respectively. In addition, the molded plate has good toughness performs well in compression resistance, shock resistance, and thermal aging resistance, which allows it to be used for a long time under 300 °C. Finally, the prepared materials are tested experimentally on an americium beryllium neutron source. The experimental results match the simulation results well.
1 February 2021 in IOP Conference Series: Earth and Environmental Science
This paper carried out an optimization design and application study on a high temprature resistant borated polyethylene shielding material, according to the nuclear power plant source characteristics and special protection requirements. The composition of borated polyethylene shielding material was optimized based on the genetic algorithm and Monte Carlo methods, then it was realized by blending modification and graft copolymerization to improve the high temperature resistant, shielding and mechanical properties. Finally, comprehensive properties such as mechanical, neutron shielding, irradiation resistance and high temperature resistance experiments were verified with the ordinary borated polyethylene and polypropylene. Those just proved the optimized borated polyethylene shielding material has excellent performance comparatively, especially it could keep complete structure in a high temperature environment up to 190°C during 48 hours, meeting the requirements of radiation protection safety for nulear power plant completely.
A novel high-temperature-resistant W-B4C-poly(4-methyl-1-pentene) (PMP) composite shielding material against neutron and gamma rays was developed and fabricated. Firstly, utilizing the 235U-induced fission spectrum as the source term, the compositional ratio of the W-B4C-PMP ternary composite was optimized using the genetic algorithm-based GENOCOPIII program coupled with MCNP simulations. Then, the composite was fabricated through coupling agent modification, melt mixing, and hot pressing. Finally, the effects of coupling modification and tungsten content on the thermomechanical properties of the composite were investigated. Results demonstrated that functional groups from the silane coupling agent KH550 were successfully grafted onto the filler surfaces. For composites containing 30 wt% modified B4C and 40 wt% modified W in the PMP matrix, the heat deflection temperature (HDT) increased by 18.5% and 19.1%, respectively, compared to their unmodified counterparts. The impact strength also improved by 31.6% and 5.0%, respectively. The variation trend of the composite’s modulus approximately followed the classical Einstein model, while its tensile strength and flexural strength conformed precisely to the model: . Thermal analysis indicated that the composites possessed a melting point exceeding 230 °C, and their thermal stability improved with increasing filler content.
Silica aerogel, a prototypical transparent nanoporous material with ultralow density and a widely tunable refractive index, is employed as a Cherenkov radiator for precision gamma-ray diagnostics in inertial confinement fusion experiments. However, its optical transmittance is highly sensitive to sol–gel chemistry. Here, silica aerogels were prepared from tetraethyl orthosilicate (TEOS), ethanol, water, and aqueous ammonia, followed by aging, solvent exchange, and supercritical drying. The study examined how catalyst, ethanol, and water concentrations regulate nanostructure and optical transmittance. Increasing ammonia content accelerated gelation, produced smaller framework particles, and enlarged the pore size and pore volume. These changes increased the transmittance at 550 nm from 79.6% for C1 to 84.9% for C7. Increasing ethanol concentration diluted TEOS and its hydrolysis products, extended gelation, and narrowed the particle-size distribution. The average particle size decreased from 21.79 to 17.01 nm, while the transmittance at 550 nm increased from 57.4% for E1 to 65.2% for E5. Water produced a non-monotonic response: insufficient water limited TEOS hydrolysis, whereas excessive water promoted structural heterogeneity. Intermediate water content provided the most favorable optical response. These findings define a process–structure–transmittance relationship in which formulation-dependent nanoscale network formation governs scattering losses and optical clarity.