Kenji Saito

Kenji Saito

Auto-generated profile, based on publicly available information

Kenji Saito

Facility for Rare Isotope Beams

Research Focus & Metrics

Academic Career Length

37Years (1990-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

2 August 2006
Verified
Conference Paper
Closed access
TWT. Warabino
T. Warabino
KSK. Saito
K. Saito
KSK. Sugiyama
K. Sugiyama
HSH. Shinonaga
H. Shinonaga
TNT. Nishida
T. Nishida

28 July 2019
Verified
Conference Paper
Closed access
PDF file
CYChongho Youn
Chongho Youn
KSKenji Saito
Kenji Saito
MFMotohiro Furuya
Motohiro Furuya
In this research, in order to predict the dynamic characteristics of a regulating valve, a mathematical model is proposed for a pneumatic control valve using a smart valve positioner (AVP300), and the dynamic characteristics of the control valve were simulated. We modeled the components of the control valve (i.e., nozzle flapper, pilot valve, Auto/Manual (A/M) screw, bleed orifice, pneumatic actuator, gland packing, and pressure reducing valve), and simulated the dynamic characteristics using SimulationX, a one-dimensional analysis software. For the nozzle flapper, we proposed a model that considers the influence of fluid force due to pressure change as well as the influence of the change in effective area by measuring the displacement, pressure, and flow rate of the nozzle flapper. The diaphragm chamber, which operates the pilot valve of the positioner, was made of transparent acrylic. The displacement of the pilot valve was measured by a laser displacement sensor, and its movement against pressure change was clarified. The sonic speed conductance and critical pressure ratio of the A/M screw and bleed orifice were determined experimentally and reflected in the model. In the pneumatic actuator, the effective cross-section of the diaphragm was obtained from the change in pressure and displacement. The change in volume was calculated from the experiment using a fixed chamber. The friction force of gland packing was modeled using static and dynamic friction forces. The experiment on the dynamic characteristics of valve displacement was performed with the input signal of the valve displacement set from 20% to 80%. A comparison of the experimental results of the valve displacement and simulation results showed good agreement. The simulation in this study is considered effective in predicting the dynamic characteristics of the control valve.

10 March 2026 in Physical Review Accelerators and Beams
Verified
Journal Article
Open access
YWYuting Wu
Yuting Wu
KSKenji Saito
Kenji Saito
ATAlex Taylor
Alex Taylor
AGAndrei Ganshyn
Andrei Ganshyn
CCChris Compton
Chris Compton
YCYoo-Lim Cheon
Yoo-Lim Cheon
A development effort to improve the performance of superconducting radio-frequency half-wave resonators (SRF HWRs) is underway at the Facility for Rare Isotope Beams (FRIB), where 220 such resonators are in operation. Our goal was to achieve an intrinsic quality factor ( Q 0 ) of ≥ 2 × 10 10 at an accelerating gradient ( E acc ) of 12 MV / m . FRIB production resonators were prepared with buffered chemical polishing. First trials of electropolishing (EP) and post-EP low-temperature baking of FRIB HWRs allowed us to reach higher gradient (15 MV/m, limited by quench) with a higher quality factor at high gradient, but Q 0 was still below our goal. Trapped magnetic flux during the Dewar test was found to be a source of Q 0 reduction. Three strategies were used to reduce the trapped flux: (i) adding a local magnetic shield (LMGS) to supplement the “global” magnetic shield around the Dewar for reduction of the ambient magnetic field; (ii) performing a “uniform cooldown” (UC) to reduce the thermoelectric currents; and (iii) using a compensation coil to further reduce the ambient field with active field cancellation (AFC). The LMGS improved the Q 0 , but not enough to reach our goal. With UC and AFC, we exceeded our goal, reaching Q 0 = 2.8 × 10 10 at E acc = 12 MV / m .