15 July 2009 in Journal of Engineering for Gas Turbines and Power
This paper provides a discussion on how degradation develops and affects the performance of the gas turbine. Because the function of a gas turbine is the result of the fine-tuned cooperation of many different components, the emphasis of this paper is on the gas turbine and its components as a system. Therefore, the interaction of components is studied in detail. An engine model is subjected to various types of degradation, and the effect on operating parameters is studied. The focus is on three areas: How does component degradation impact the operating points of the engine compressor, how does component degradation impact full load and part load gas turbine performance characteristics, and how does component degradation impact measurable engine operating parameters. Experimental data are provided that supports the theoretical conclusion. Parameters that indicate levels of degradation are outlined, thus providing guidance for condition monitoring practice.
1 April 2015 in Journal of Engineering for Gas Turbines and Power
An investigation of the effectiveness of online combustion turbine axial compressor washing using various purity grade waters and commercial washing detergents was performed. For this project, blade surface fouling dirt was obtained from gas turbine axial compressor blades installed at various field sites. The dirt was analyzed to determine consistency of typical blade surface fouling materials. A representative dirt formula and blade coating procedure was developed so that comparative tests could be performed using various cleaning fluids. Dirt coated blades were installed in a wind tunnel capable of simulating compressor operating conditions. A spray nozzle upstream of the blade test section was used for washing blades with five different test liquids to determine the effectiveness or advantages of any liquid. Once this testing was completed, a similar test setup was then utilized to inject a mixture of formulated fouling dirt and the various online cleaning liquids upstream of the blade into the wind tunnel to assess redeposit characteristics. The effect of high-purity water versus regular water on fouling dirt was also studied in separate residue experiments. Results indicate that spraying cleaning fluid into a flowing air stream is a viable means of cleaning a compressor blade. Each of the fluids was able to clean the test blade at both low and high air velocities and at different blade incident angles. Within the parameters/fluids tested, the results indicate that: (1) The blade cleaning is primarily a mechanical function and does not depend on the type of fluid used for cleaning. The results showed that most of the cleaning occurs shortly after the cleaning fluid is introduced into the flow stream. (2) Dirt removed from the blades may redeposit in other areas as the cleaning fluid is evaporated. Redeposit occurred in flow recirculation zones during the cleaning tests, and heated flow tests demonstrated dirt deposit in the presence of a cleaning fluid. In addition, the type of fluid used for cleaning has no effect on the redeposit characteristics of the dirt. (3) Blade erosion was not found to be a significant issue for the short durations that online water-washing was performed. However, uncontrolled water-washing (or overspray) for extended periods of time did result in measureable leading and trailing edge blade erosions.
4 October 2016 in Journal of Engineering for Gas Turbines and Power
Fouling of compressor blades is an important mechanism leading to performance deterioration in gas turbines over time. Experimental and simulation data are available for the impact of specified amounts of fouling on the performance as well as the amount of foulants entering the engine for defined air filtration systems and ambient conditions. This study provides experimental data on the amount of foulants in the air that actually stick to a blade surface for different conditions. Quantitative results both indicate the amount of dust as well as the distribution of dust on the airfoil, for a dry airfoil, and also the airfoils that were wet from ingested water, in addition to, different types of oil. The retention patterns are correlated with the boundary layer shear stress. The tests show the higher dust retention from wet surfaces compared to dry surfaces. They also provide information about the behavior of the particles after they impact on the blade surface, showing for a certain amount of wet film thickness, the shear forces actually wash the dust downstream and off the airfoil. Further, the effect of particle agglomeration of particles to form larger clusters was observed, which would explain the disproportional impact of very small particles on boundary layer losses.
1 March 2012 in International Journal of Rotating Machinery
When considering gas compressor stations for pipeline projects, the economic success of the entire operation depends to a significant extent on the operation of the compressors involved. In this paper, the basic factors contributing to the economics are outlined, with particular emphasis on the interaction between the pipeline and the compressor station. Typical scenarios are described, highlighting the fact that pipeline operation has to take into account variations in load.
31 March 2021 in Journal of Engineering for Gas Turbines and Power
Compressor fouling is one of the main causes of gas turbine performance degradation. Microsized particles adhere to the blade surfaces increasing the surface roughness and modifying the airfoil shape. In this work, the contamination of the Allison 250 C18 multistage compressor engine with four sorts of micrometric dust has been provided. The tests were performed changing the relative humidity (RH) at the compressor inlet and the unit rotational speed. After each test, a photographic inspection of the internal fouled parts has been realized and the digital pictures have been analyzed employing an image processing package. The deposit's build-up of stator vanes and rotor blades has been postprocessed and the most affected regions of each compressor stage have been highlighted. Besides, a numerical simulation of the machine has been performed. The numerical flow field has been used to highlight the blade regions, which show the most favorable conditions for particle deposition. A theoretical model has been applied to the flow field to simulate the particle deposition. The combination of the deposition model with the results of the numerical simulations gives the chance to better understand the experimentally founded deposition patterns. Those results have been finally compared to the pictures of the patterns. The possibility to detect and measure the deposition patterns on a rotating test rig and the comparison with models and experiments gave the possibility to assess in detail the particle deposition phenomenon on a multistage axial compressor flow path.
19 September 2017 in Journal of Engineering for Gas Turbines and Power
The force acting on centrifugal compressors is an important parameter to be considered throughout the operating life of these turbomachines. When the compressor is operating in surge conditions, these forces can become highly dangerous for the mechanical and aerodynamic structures. This instability is usually avoided in industrial applications, but the antisurge system may not react in time when emergency shutdowns or power failures take place. During these rapid transients, surge can develop, generating unsteady forces which can harm the close clearance components of the compressor. Therefore, the capability to predict the characteristics and the dynamics of these surge forces would allow the estimation of the off-design fatigue cycles produced on these components by surge. Currently, no validated method exists to predict the frequency and amplitude of the surge forces and determine the potential damage of these components. In this paper, a lumped parameter model, developed by using the bond graph approach to predict the dynamic surge fluid-dynamic oscillations, is presented. The model requires the geometry and the steady-state performance maps of the compressor as inputs, together with the piping system configuration characteristics. The simulator is provided with a supplementary tool to estimate the axial force frequency and amplitude, taking into consideration all the contributions to the axial fluid-dynamic thrust, the stiffness-damping of the thrust bearing, and the mass of the rotor. The model was tuned and validated using the test case axial force data from the Southwest Research Institute (SWRI) facility. The model has shown good agreement with the experimental results which implies that it can offer significant information about the severity of a surge event and the quantification of the machine performance losses together with possible damage to the close clearance components. This study is a first important step that can lead to schedule optimization for maintenance and repair activities.