17 January 2018 in IEEE Antennas and Wireless Propagation Letters
This letter presents a wideband transmitarray (TA) with reduced profile. A novel unit cell based on a wideband bandpass filter is developed and applied to the design of the TA. The TA consists of two identical tri-layer frequency selective surfaces (FSS), thus it has a lower profile compared to traditional designs which use at least four FSS layers separated by quarter-wavelength air gaps to obtain the 360-degree phase shift range. The FSS has a pair of square patches printed on the top and bottom layers, and a square slot loaded by four microstrips printed on the middle layer. The phase shift is achieved by simultaneously adjusting the size of the square patches. Within the frequency band of interest, the developed unit cell shows low insertion loss and sufficient phase shift range. An equivalent circuit model is developed to better understand the operating principles of the FSS. To validate the design concept, one prototype operating at 13.5GHz is designed, fabricated and measured. The measurement results show that the designed TA achieves 16% 1-dB gain bandwidth and 60% aperture efficiency. The developed unit cell has symmetric configurations so it can also be applied to the design of dual-polarized or circularly polarized TAs.
20 June 2019 in IEEE Transactions on Antennas and Propagation
This paper presents a novel hybrid design technique to minimize the number of layers of the transmitarray (TA) panel while maintaining 360o phase shift range. Two types of unit cells, the receive-transmit unit cell and the frequency selective surface (FSS), are placed in the same aperture. The resulting TA panel is very thin but does not sacrifice the radiation efficiency of the array. The receive-transmit unit cell is an aperture coupled square patch, and the FSS unit cell is a novel wide bandpass FSS. Both types of unit cells have three conductive layers and are printed on two substrates with a total thickness of 0:07λ0. The developed hybrid TA shows better gain than a homogeneous TA using the same elements. Meanwhile, it has comparable radiation performance but with a much lower profile compared to conventional FSS-based TA designs that use several substrates separated by air layers. To verify the design concept, two hybrid TAs of different sizes with central frequency at 13.3 GHz were designed and fabricated. The measurements show that the TAs have at least 6:7% 1-dB gain bandwidth and higher than 30% aperture efficiency. Comparing to the existing ultra-thin designs of similar panel thickness, the presented TAs do not suffer from the phase quantization loss and achieve better or similar bandwidths.
1 December 2000 in International Journal of Bifurcation and Chaos
10 April 2007 in IEEE Transactions on Microwave Theory and Techniques
This paper describes how circuit and system models are derived for antennas from measurement of the input reflection coefficient. Circuit models are used to optimize the antenna performance and to calculate the radiated power and the transfer function of the antenna. System models are then derived for transmitting and receiving antennas. The most important contribution of this study is to show how microwave structures can be integrated into the simulation of digital communication systems. This enables system designers to predict the effect of the microwave subsystem on the digital signals and calculate the resulting bit error rate
5 July 2018 in IEEE Transactions on Antennas and Propagation
Antenna frequency response can be characterized in terms of effective aperture and gain. Antennas can also be characterized as a two-port network to ascertain the antenna transfer function (S21). This characterization is important in point-to-point (P2P) communication, as the frequency response can vary due to changes in the radiation pattern in the physical channel. This paper presents a process to investigate the frequency response of a wideband antenna in order to identify the best orientation of the antenna for P2P communication. The process predicts the antenna’s effective aperture and gain for each orientation. An equivalent circuit for the wideband antenna is also derived to obtain the total radiated power. The frequency-variant radiation pattern is ascertained from the S21 phase obtained from the equivalent circuit. For each orientation, the S21 phase is analyzed based on the linear, minimum, and all-pass phase components, which enables the derivation of an equivalent circuit. The variation of group delay for each orientation is also obtained and compared. The measurements between two identical antennas at the two orientations with a free-space channel were then modeled for simulation in a digital system. This simulation predicts the antenna effects for the two orientations used. Finally, this process was validated by using a non-minimum phase monopole ultra-wideband (UWB) antenna.