1 February 2021 in IEEE Transactions on Circuits and Systems I: Regular Papers
This paper presents a low-profile and autonomous piezoelectric energy harvesting system consisting of an extraction rectifier and a maximum power point tracking (MPPT) circuit for powering portable electronics. Synchronized switch harvesting on capacitor-inductor (SSHCI) technique with its unique two-step voltage flipping process is utilized to downsize the ponderous external inductor and extend application areas of such harvesting systems. SSHCI implementation with small flipping inductor-capacitor combination enhances voltage flipping efficiency and accordingly attains power extraction improvements over conventional synchronized switch harvesting on inductor (SSHI) circuits utilizing bulky external components. A novel MPPT system provides robustness of operation against changing load and excitation conditions. Innovation in MPPT comes from the refresh unit, which continually monitors excitation conditions of piezoelectric harvester to detect any change in optimum storage voltage. Compared with conventional circuits, optimal flipping detection inspired from active diode structures eliminates the need for external adjustment, delivering autonomy to SSHCI. Inductor sharing between SSHCI and MPPT reduces the number of external components. The circuit is fabricated in 180 nm CMOS technology with 1.23 mm 2 active area, and is tested with custom MEMS piezoelectric harvester at its resonance frequency of 415 Hz. It is capable of extracting 5.44x more power compared to ideal FBR, while using $100~\mu $ H inductor. Due to reduction of losses through low power design techniques, measured power conversion efficiency of 83% is achieved at 3.2 V piezoelectric open circuit voltage amplitude. Boosting of power generation capacity in a low profile is a significant contribution of the design.
15 March 2019 in IEEE Transactions on Circuits and Systems I: Regular Papers
This paper presents an efficient hybrid energy harvesting interface to synergistically scavenge power from electromagnetic (EM) and piezoelectric (PE) sources, and drive a single load. The EM harvester output is rectified through a self-powered active doubler structure, and stored on a storage capacitor. The stored energy is then transferred to the PE harvester to increase the damping force and charge extraction. The total synergistically extracted power from both harvesters is more than the power obtained from each independently. The hybrid operation is validated through a compact and wearable platform that includes custom designed EM and PE harvesters for scavenging energy from human motion. The system supplies 1-3.4 V output for powering up wireless sensor nodes with a wide range of vibration frequency, and generates between 1-100 μW at 90% maximum power conversion efficiency. The solution has superior power generation performance compared to previous stand-alone systems in the literature.
24 August 2021 in IEEE Access
This article presents an area efficient fully autonomous piezoelectric energy harvesting system to scavenge energy from periodic vibrations. Extraction rectifier utilized in the system is based on synchronized switch harvesting on inductor (SSHI) technique which enables system to outperform standard passive rectifiers. Compared to conventional SSHI circuits, enhanced SSHI (E-SSHI) system proposed in this paper uses a single low-profile external inductor in the range of $\mu \text{H}$ ’s to reduce overall system cost and volume, hence broadening application areas of such harvesting systems. Furthermore, E-SSHI does not include any negative voltage converter circuit and therefore, it offers area efficient AC/DC rectification. Detection of optimal voltage flipping times in E-SSHI technique is conducted autonomously without any external calibration. Energy transfer circuit provides control over how much energy is delivered from E-SSHI output to electronic load. The proposed system is fabricated in 180 nm CMOS process with 0.28 mm 2 active area. It is tested using a commercial piezoelectric transducer MIDE V22BL with periodic excitation. Measured results reveal that E-SSHI circuit is capable of extracting up to 5.23 and 4.02 times more power compared with an ideal full-bridge rectifier at 0.87 V and 2.6 V piezoelectric open circuit voltage amplitudes (V OC, P ), respectively. A maximum voltage flipping efficiency of 93% is observed at V OC,P = 3.6 V, owing to minimized losses on charge flipping path. Measured results are compared with state-of-the-art interface circuits. Comparison shows that E-SSHI design offers a huge step towards miniaturized harvesting systems thanks to its low-profile and fully autonomous design.
1 November 2019 in Journal of Physics: Conference Series
This paper presents a self-powered interface circuit to rectify and manage the AC output of the piezoelectric energy harvesters (PEH) by utilizing Self-Investing Synchronous Electric Charge Extraction technique (SI-SECE). The system invests charges from the battery to PEH to improve the electromechanical coupling factor and consequently the energy extraction by utilizing only one external component. The circuit was implemented in 180 nm CMOS technology where high voltage (HV) MOS transistors are utilized to tolerate high open circuit output voltages of PEHs. MEMS PEH with 4.7 nF inherent capacitance has been used to charge a 1 μF storage capacitor. Proposed interface circuit extracts 18.55 μW that is 33 % more than traditional SECE (13.95 μW) for 250 Hz PEH excitation frequency and 2.3 V piezoelectric open circuit voltage amplitude. At the output power of 48.5 μW, maximum power conversion efficiency of 62.4% is achieved as charge investment and corresponding conduction and switching losses on investing transistors. SI-SECE delivers power with 4.5x relative performance improvement over on-chip full-bridge rectifier.