18 August 2017 in Nuclear Fusion
1 July 2013 in Journal of Nuclear Materials
22 July 2019 in Nuclear Fusion
4 June 2009 in Nuclear Fusion
Fuel retention, a crucial issue for next step devices, is assessed in present-day tokamaks using two methods: particle balance performed during shots and post-mortem analysis carried out during shutdowns between experimental campaigns. Post-mortem analysis generally gives lower estimates of fuel retention than integrated particle balance. In order to understand the discrepancy between these two methods, a dedicated experimental campaign has been performed in Tore Supra to load the vessel walls with deuterium (D) and monitor the trapped D inventory through particle balance. The campaign was followed by an extensive post-mortem analysis phase of the Tore Supra limiter. This paper presents the status of the analysis phase, including the assessment of the D content in the castellated tile structure of the limiter. Indeed, using combined surface analysis techniques, it was possible to derive the relative contributions of different zones of interest on the limiter (erosion, thick deposits, thin deposits), showing that the post-mortem inventory is mainly due to codeposition (90% of the total), in particular due to gap deposits. However, deuterium was also evidenced deep into the material in erosion zones (10% of the total). At the present stage of the analysis, 50% of the inventory deduced from particle balance has been found through post-mortem analysis, a significant progress with respect to previous studies (factor 8–10 discrepancy). This shows that post-mortem analysis can be consistent with particle balance provided specific procedures are implemented (dedicated campaign followed by extensive post-mortem analysis). Both techniques are needed for a reliable assessment of fuel retention in tokamaks, giving complementary information on how much and where fuel is retained in the vessel walls.
6 May 2022 in Nuclear Fusion
ITER will operate with a tungsten divertor, a material featuring surface morphology changes when exposed to helium plasmas, in particular the formation of the so called tungsten fuzz under specific conditions. Investigating interactions between tungsten plasma facing components and helium plasmas in a tokamak environment is therefore a key point to consolidate predictions for the ITER divertor performance and lifetime. To this end, a dedicated helium campaign was performed in the full tungsten WEST tokamak, cumulating ∼2000 s of repetitive L mode discharges. It is shown that conditions for tungsten fuzz formation, as derived from linear devices experiments (incident helium energy E inc > 20 eV, helium fluence >1024 He/m2, surface temperature T surf > 700 °C), were met in the outer strike point (OSP) area of the inertially cooled tungsten divertor elements of WEST. Preliminary inspection of the components after the campaign did not show visible signs of surface modification, but points to significant net erosion in the OSP area. An extensive post mortem analysis is now ongoing to confirm these first indications. These results underline that the complex balance between erosion/redeposition (in particular linked to impurities) and tungsten fuzz formation needs to be taken into account in tokamak conditions.
12 October 2023 in Nuclear Fusion
After the second Deuterium–Tritium Campaign (DTE2) in the JET tokamak with the ITER-Like Wall (ILW) and full tritium campaigns that preceded and followed after the DTE2, a sequence of fuel recovery methods was applied to promote tritium removal from wall components. The sequence started with several days of baking of the main chamber walls at 240 °C and at 320 °C. Subsequently, baking was superimposed with Ion-Cyclotron Wall Conditioning (ICWC) and Glow Discharge Conditioning (GDC) cleaning cycles in deuterium. Diverted plasma operation in deuterium with different strike point configurations, including a Raised Inner Strike Point (RISP) configuration, and with different plasma heating—Ion Cyclotron Resonance Frequency (ICRF) and Neutral Beam Injection (NBI)—concluded the cleaning sequence. Tritium content in plasma and in the pumped gas was monitored throughout the experiment. The applied fuel recovery methods allowed reducing the residual tritium content in deuterium NBI-heated plasmas to about 0.1% as deduced from neutron rate measurements. This value is well below the requirement of 1% set by the maximum 14 MeV fusion neutron budget allocated in the ensuing deuterium plasma campaign. The quantified tritium removal over the course of the experiment was atoms or g with ∼58% attributed to baking, ∼12.5% to ICWC, ∼26% to GDC, and ∼3.5% to first low power RISP plasmas. The experimentally estimated amount of removed tritium is in good agreement with long-term tritium accounting by the JET tritium reprocessing plant, in which the unaccounted amount was reduced by g after the cleaning experiment.