Davut Erdem Sahin

Davut Erdem Sahin

Auto-generated profile, based on publicly available information

Davut Erdem Sahin

Yalova University

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 June 2023 in Journal of Thermoplastic Composite Materials
Verified
Journal Article
Closed access
OOOsman Ozenc
Osman Ozenc
MDMehmet Akif DUNDAR
Mehmet Akif DUNDAR
DSDavut Erdem Sahin
Davut Erdem Sahin
Effects of the addition of hemp fiber particles on the compressive and flexural behaviors of an industrially important amorphous thermoplastic, Acrylonitrile-Butadiene-Styrene (ABS), were investigated for the first time in this study. Particles with a size of 67–500 μm were first extracted from 10% NaOH alkaline-treated hemp fibers, and then incorporated into ABS at three various weight ratios (1wt%, 5wt% and 10wt%). Compression and three-point bending tests results revealed that both the compressive and flexural modulus of ABS increase with increasing particle content, but its compressive post-yield and flexural strengths decrease as enhancing particle content. The test results also showed that increasing particle content results in a significant improvement in the compressive modulus of ABS, but a slight enhancement in its flexural modulus. The notch-impact test results revealed that the impact strength of ABS is adversely affected by the incorporation of hemp fiber particles. The FT-IR (Fourier Transform Infrared Spectroscopy) analysis results indicated that mechanical bonding is formed between matrix and natural particles rather than chemical bonding. The SEM (Scanning Electron Microscopy) results put forth that the observed decrease in both the compressive post-yield and flexural strength is mainly due to the lack of strong mechanical bonding between ABS and particles. The three-point bending test data of the materials were satisfactorily reproduced using the linear Drucker-Prager material model in Abaqus engineering software.

29 July 2022 in Journal of Vibration Engineering & Technologies
Verified
Journal Article
Closed access
PDF file
DSDavut Erdem Sahin
Davut Erdem Sahin

25 February 2025 in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
Verified
Journal Article
Closed access
MDMehmet Akif DUNDAR
Mehmet Akif DUNDAR
OOOsman Ozenc
Osman Ozenc
DSDavut Erdem Sahin
Davut Erdem Sahin
This study explores a relatively under-researched area concerning the influence of loading rate on the flexural properties of particulate-filled bio-composites and the effects of incorporating natural particles on their damage parameters. To investigate these aspects, three-point flexural tests were conducted across a range of bending speeds from 0.1 mm/s to 10 mm/s. The material under study consisted of Acrylonitrile-Butadiene-Styrene (ABS) reinforced with hemp particles at varying contents (1–10 wt%). Additionally, the impact of hemp particle incorporation on the damage parameters of ABS was evaluated through cyclic loading-unloading tension tests. The flexural test results demonstrated a consistent increase in the flexural modulus of ABS with rising strain rates, irrespective of the hemp particle content. In contrast, the percentage reduction in flexural strength exhibited a diminishing trend as the bending rate increased. Findings from the cyclic loading-unloading tension tests further revealed that the addition of hemp particles intensifies the degradation of ABS's elastic modulus, with this effect becoming more pronounced at higher particle contents. Finite element simulations incorporating the experimentally determined damage parameters successfully reproduced the flexural load-displacement curves of the materials at different strain rates. These simulations corroborated the experimental findings and offered insights for optimizing material performance.

20 July 2019
Verified
Book Chapter
Closed access
PDF file
MCM. Amin Changizi
M. Amin Changizi
ISIon Stiharu
Ion Stiharu
DŞD. Erdem Şahin
D. Erdem Şahin