Annika Kienzlen

Annika Kienzlen

Auto-generated profile, based on publicly available information

Annika Kienzlen

Institute for Control Engineering of Machine Tools and Manufacturing Units University of Stuttgart,Stuttgart,Germany

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 November 2023 in IEEE Open Journal of Engineering in Medicine and Biology
Verified
Journal Article
Open access
MZManuela Zimmer
Manuela Zimmer
EBElsa K. Bunz
Elsa K. Bunz
TETobias Ehring
Tobias Ehring
BKBenedikt Kaiser
Benedikt Kaiser
AKAnnika Kienzlen
Annika Kienzlen
MZManuel Zürn
Manuel Zürn
Goal: Skeletal muscle mechanics can be assessed in vivo using shear wave elastography. However, the impact of pennation angle on shear wave velocity (SWV) remains unclear. This study aims to quantify the effect by automatically aligning the ultrasound probe with muscle fiber orientation. Methods: We propose an automatic ultrasound probe alignment system and compare it to manual and no alignment. SWV of the gastrocnemius medialis muscle of ten volunteers was measured during rest and isometric contractions. Results: The SWV was different between the conditions ( $p~=~0.008$ ). The highest SWV was obtained during the automatic alignment and differences between the conditions were most pronounced during high-level contractions. The automatic system yielded more accurate alignment compared to a manual operator ( $p~=~0.05$ ). Conclusions : The present study indicates that pennation angle affects SWV, hence muscle fiber orientation must be considered to reliably interpret SWV. Using automatic alignment systems allows for more accurate alignment, improving the methodology of ultrasound elastography in skeletal muscles.

27 October 2020 in Forschung im Ingenieurwesen
Verified
Journal Article
Open access
PDF file
AKA. Kienzlen
A. Kienzlen
JWJ. Weißen
J. Weißen
AVA. Verl
A. Verl
SGS. Göttlich
S. Göttlich
Zusammenfassung: Moderne Fertigungssysteme sind komplexe, umfangreiche Systeme. Eine sorgfältige Planung des gesamten Fertigungssystems ist erforderlich, um langfristig effektiv zu produzieren und Gewinne zu erzielen. Bei der Layoutplanung dieser Systeme muss berücksichtigt werden, dass der Materialfluss zwischen einzelnen Stationen zuverlässig und reibungslos funktioniert. Die virtuelle Inbetriebnahme (VIBN) ermöglicht es, das Zusammenspiel von Anlagenlayout und Steuerungssystem, welches das optimale Design der Anlage wesentlich beeinflusst, frühzeitig zu testen. Konzeptionsfehler und Engpässe, die die Performance beeinflussen, können im Voraus erkannt und behoben werden. Für die VIBN wird die reale Anlage durch ein Simulationsmodell ersetzt, um im Zusammenspiel mit dem realen Steuerungssystem Tests durchführen zu können.In dieser Arbeit wird ein Vorgehensmodell entworfen, anhand dessen die Leistungsfähigkeit von Maschinen und Anlagen mit besonders hohem Materialflussaufkommen analysiert und das Layout bewertet werden kann. Wichtige Leistungskenngrößen wie die Taktzeit und Auslastung einzelner Bestandteile des Fertigungssystem können hinsichtlich ihrer Realisierbarkeit überprüft werden. Durch Testläufe an einem Simulationsmodell des Materialflusses werden Fehler und Engpässe, welche die Performance der Anlage negativ beeinflussen, frühzeitig erkannt. Zur Verbesserung des Layouts wird dabei ein Flussmodell basierend auf einer Erhaltungsgleichung eingesetzt. Das neue Simulationsmodell ermöglicht insbesondere die Simulation großer Mengen an Materialien bei gleichzeitig geringer Berechnungsdauer. Für die Validierung der Ergebnisse werden Parameter festgelegt, die als Indikator für die Leistung von Materialflusssystemen dienen und in einer ingenieurstechnischen Simulation gemessen werden können. Das enge Zusammenspiel verschiedener Simulationen ermöglicht die Validierung und effiziente Verbesserung des Layouts.

4 November 2024
Verified
Conference Paper
Closed access
AKAnnika Kienzlen
Annika Kienzlen
AVAlexander Verl
Alexander Verl
While the importance of virtual commissioning is increasing and not only individual machines but also production lines are being simulated, the simulation of material flow for numerous piece goods is still a challenge. Combining models in a multi-scale simulation can exploit their advantages. The macroscopic flow model excels at modeling the behavior of large quantities of piece goods, however, it cannot provide information about individual piece goods. This led to the approach of the combination with a microscopic physics-based model in a multi-scale material flow simulation. To switch between models, the coordinates of the positions (microscopic) have to be translated in one direction into the material description of the macroscopic flow model (the density distribution). In the other direction, the density distribution has to be translated into the coordinates of the positions, leading to a computationally intensive optimization problem. This paper develops various methods for finding a start solution and compares them to a method of the state of the art. The evaluation is based on their accuracy with reference to various parameters of the data set. The results show the best accuracies for the method which traverses the density distribution and calculates the sum of the densities until it matches a single piece good. Depending on the accuracy required, it may be possible to use the start solution directly without further optimization.