Christian Schlette

Christian Schlette

Auto-generated profile, based on publicly available information

Christian Schlette

SDU Center for Large Structure Production, University of Southern Denmark 2 , Innovationsvejen 2, Munkebo 5330

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 July 2021 in IEEE Robotics and Automation Letters
Verified
Journal Article
Closed access
JHJuan Heredia
Juan Heredia
CSChristian Schlette
Christian Schlette
MKMikkel Baun Kjaergaard
Mikkel Baun Kjaergaard
Traditionally, the objective of industrial production focuses on fast and low-cost production, regardless of resources and energy consumption (EC). However, in alignment with the UN Sustainable Development Goals (SDG), governments worldwide have proposed regulations to reduce resources and energy. In their production lines, an increasing number of companies are using collaborative robots (cobots). Cobots are programmed to accomplish their task as fast as possible, ignoring the robot's EC. This letter estimates the cobot EC from individual instructions of user-defined robot programs. Thus, the user has an additional design parameter to create energy-optimal programs. In the literature, current EC estimation models for manipulators are not reliable or have not been assessed to test the model's reliability. Our modeling methodology possesses three steps: motion planning, dynamic model, and EC model. Using cobots of different sizes (UR3e and UR10e) and loading, we collected over 55000 samples per case and trained the model to identify the model's unknown parameters. The model estimated the power consumption of a testing dataset with a maximum RMS error of 6 [W] - 3.85%. In the final experiment, the complete system was tested using a user-defined program composed of six instructions. The results showed an accurate estimation of the power profile with an RMS error of 2.39 [W] and 4.23 [W] for UR3e and UR10e.

7 November 2019 in Advanced Robotics
Verified
Journal Article
Closed access
CSC. Schlette
C. Schlette
ABAnders Glent Buch
Anders Glent Buch
FHF. Hagelskjær
F. Hagelskjær
III. Iturrate
I. Iturrate
DKD. Kraft
D. Kraft
TTT. N. Thulesen
T. N. Thulesen
To support shifting to high mix/low volume production, manufacturers in high wage countries aim for robotizing their production operations – with a special focus on the late production phases, where robotic assembly cells are then confronted with any complexities resulting from part and product varieties. The ‘World Robot Challenge 2018’ (WRC 2018) emulated such high mix/low volume production scenarios in a competition taking place in Tokyo, Japan. As part of our activities in SDU's newly founded I4.0 Lab, we integrated and advanced our experiences and developments from our various R & D projects in a novel robotic assembly cell design to compete in the WRC 2018. This article describes the system architecture as well as main aspects of its implementation regarding robot control, robot programming and computer vision and how they contributed to winning the challenge. Due to the application of collaborative robots, the cell design allows for operation without fences. Hence, multiple copies of the cell can be arranged in a highly reconfigurable, highly adaptable matrix structure in which several production flows can be handled concurrently. This concept was demonstrated by the installation of a duplicate cell that allowed for parallel developments on two cells and prolonged development also after shipping the first cell to Japan.

26 December 2019 in Advanced Robotics
Verified
Journal Article
Closed access
FDFelix von Drigalski
Felix von Drigalski
CSChristian Schlette
Christian Schlette
MRMartin Rudorfer
Martin Rudorfer
NCNikolaus Correll
Nikolaus Correll
JTJoshua C. Triyonoputro
Joshua C. Triyonoputro
TWTetsuyou Watanabe
Tetsuyou Watanabe
The Industrial Assembly Challenge at the World Robot Summit was held in 2018 to showcase the state-of-the-art of autonomous manufacturing systems. The challenge included various tasks, such as bin picking, kitting, and assembly of standard industrial parts into 2D and 3D assemblies. Some of the tasks were only revealed at the competition itself, representing the challenge of ‘level 5’ automation, i.e. programming and setting up an autonomous assembly system in less than one day. We conducted a survey among the teams that participated in the challenge and investigated aspects such as team composition, development costs, system setups as well as the teams' strategies and approaches. An analysis of the survey results reveals that the competitors have been in two camps: those constructing conventional robotic work cells with off-the-shelf tools, and teams who mostly relied on custom-made end effectors and novel software approaches in combination with collaborative robots. While both camps performed reasonably well, the winning team chose a middle ground in between, combining the efficiency of established play-back programming with the autonomy gained by CAD-based object detection and force control for assembly operations.

3 August 2023 in IEEE Robotics and Automation Letters
Verified
Journal Article
Closed access
JHJuan Heredia
Juan Heredia
RKRobin Jeanne Kirschner
Robin Jeanne Kirschner
CSChristian Schlette
Christian Schlette
SASaeed Abdolshah
Saeed Abdolshah
SHSami Haddadin
Sami Haddadin
MKMikkel Baun Kjægaard
Mikkel Baun Kjægaard
Limited resources and resulting energy crises occurring all over the world highlight the importance of energy efficiency in technological developments such as robotic manipulators. Efficient energy consumption of manipulators is necessary to make them affordable and spread their application in the future industry. Previously, the power consumption of the robot motion was the main factor considered in the evaluation of energy efficiency. Lately, the paradigm in industrial robotics shifted towards lightweight robot manipulators which require a new investigation on the disaggregation of robot energy consumption. In this paper, we propose a novel pipeline to identify and disaggregate the energy use of mechatronic devices and apply it to lightweight industrial robots. The proposed method allows the identification of the electronic components consumption, mechanical losses, electrical losses, and required mechanical energy for robot motion. We evaluate the pipeline and understand the distribution of energy consumption using four different manipulators, namely, Universal Robot's UR5e, UR10e, Franka Emika's FR3, and Kinova Gen3. The experimental results show that most of the energy (60–90%) is consumed by the electronic components of the robot control box. Using this knowledge, the approaches to further optimize their energy consumption need to shift towards efficient robot electronic design instead of efficient robot mass distribution or motion control. Finally, our disaggregation pipeline allows an understanding of the power consumption of any mechatronic device and thus enables deliberate optimization of energy consumption.

12 August 2023 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
Ahmed Magdy Ahmed ZakiAhmed Magdy Ahmed Zaki
Ahmed Magdy Ahmed Zaki
Marco CarnevaleMarco Carnevale
Marco Carnevale
CSChristian Schlette
Christian Schlette
Hermes GibertiHermes Giberti
Hermes Giberti
In production systems characterized by small batches and high customization levels, operations are required to be flexible to adapt to different products within the shortest possible time and with the minimum effort for system setup. Contact-based operations such as surface finishing, polishing, deburring, and material deposition are mandatory in the fabrication of numerous products. To maintain consistent performance over time, many of these operations require a high level of accuracy, both in end-effector positioning and contact force level. This paper proposes a robotic solution to generate the robot working trajectory for contact-based operations over the external surface of unknown objects of which a digital model is not available or different from the actual state of the workpiece. The paper introduces the integration process of RGBD images to construct a 3D model and its elaboration to extract the workpiece. Different searching subroutines have been developed to select different areas of the workpiece based on the operation to be carried on and generate the related trajectory. The evaluation metric of the proposed robotic solution is given by the stability of the contact force exerted by the robotic tool and the error between generated and the actually followed trajectory due to the depth estimation of a low-cost camera. A few millimeters of the inaccuracy of the trajectory are obtained; these inaccuracies are compensated using force control. Different tests with different nominal values of the force control loop are carried out. Statistical analysis shows that the mean values of the contact force obtained coincide with the nominal value of the single tests.

11 August 2025 in Sensors
Verified
Journal Article
Open access
PDF file
JBJuan Bravo-Arrabal
Juan Bravo-Arrabal
ZCzhuoqi cheng
zhuoqi cheng
JFJ. Jesús Fernández-Lozano
J. Jesús Fernández-Lozano
JGJose Antonio Gomez-Ruiz
Jose Antonio Gomez-Ruiz
CSChristian Schlette
Christian Schlette
AGAlfonso García
Alfonso García
The integration of robotics and mobile networks (5G/6G) through the Internet of Robotic Things (IoRT) is revolutionizing telemedicine, enabling remote physician participation in scenarios where specialists are scarce, where there is a high risk to them, such as in conflicts or natural disasters, or where access to a medical facility is not possible. Nevertheless, touching a human safely with a robotic arm in non-engineered or even out-of-hospital environments presents substantial challenges. This article presents a novel IoRT approach for healthcare in or from remote areas, enabling interaction between a specialist’s hand and a robotic hand. We introduce the IoRT-in-hand: a smart, lightweight end-effector that extends the specialist’s hand, integrating a medical instrument, an RGB camera with servos, a force/torque sensor, and a mini-PC with Internet connectivity. Additionally, we propose an open-source Android app combining MQTT and ROS for real-time remote manipulation, alongside an Edge–Cloud architecture that links the physical robot with its Digital Twin (DT), enabling precise control and 3D visual feedback of the robot’s environment. A proof of concept is presented for the proposed tele-robotic system, using a 6-DOF manipulator with the IoRT-in-hand to perform an ultrasound scan. Teleoperation was conducted over 2300 km via a 5G NSA network on the operator side and a wired network in a laboratory on the robot side. Performance was assessed through human subject feedback, sensory data, and latency measurements, demonstrating the system’s potential for remote healthcare and emergency applications. The source code and CAD models of the IoRT-in-hand prototype are publicly available in an open-access repository to encourage reproducibility and facilitate further developments in robotic telemedicine.