16 October 2018 in Journal of Engineering for Gas Turbines and Power
Ever-increasing demand for cleaner energy is driving the need for higher power density turbomachinery while reducing cost and simplifying design. Gas-lubricated bearings are representing one of the enabling technologies that can help maximize these benefits and have been successfully implemented into turbomachinery applications with rotors weights in the order few kg's. However, load capacity and damping limitations of existing gas bearing technologies prevent the development of larger size oil-free drive trains in the MW power output range. Compliantly damped hybrid gas bearings (CHGBs) were introduced as an alternative design to overcome these limitations by providing external pressurization to discrete tilting pads while retaining flexibility in the bearing support to help tolerate misalignment and rotor-pad geometry changes. Additionally, the CHGB concept addresses damping entitlement through the application of bearing support dampers such as metal mesh. An alternative CHGB design, featuring a novel hermetically seal squeeze film damper (HSFD) in the bearing support, was introduced as alternative approach to metal mesh dampers (MMDs) to further improve bearing damping. This paper details the rotordynamic characterization of a CHGB with modular HSFD for various operating conditions. Direct and cross-coupled stiffness and damping coefficients are presented for different rotor speeds up to 12,500 rpm, frequencies of excitation between 20 and 200 Hz, bearing loads between 200 and 400 lbf, and external hydrostatic pressures reaching 180 psi. Direct comparisons to experimental results for a CHGB using MMD show 3× increase in direct damping levels when using HSFD in the compliant bearing support. In addition to the experimental results, an analytical model is presented based on the implementation of the isothermal compressible Reynolds equation coupled to a flexible support possessing a pad with three degrees-of-freedom. The numerical results capture the direct stiffness and frequency dependency but underpredict the absolute values for both cases when compared to experimental data.
20 September 2019 in Journal of Engineering for Gas Turbines and Power
This paper focuses on an integral gas-film lubricated bearing concept developed to enable the oil-free operation of super-critical carbon dioxide (sCO2) turbomachinery. The externally pressurized tilting pad bearing concept possesses a flexible bearing support with an integral hermetically sealed squeeze film damper. Unlike the past concepts using modular hermetic squeeze film dampers presented, the bearing design in this work utilizes advanced manufacturing methods to yield an integral single piece design in efforts to reduce space envelope, cost, and improve overall design reliability. The paper advances a detailed description of the bearing design and identification of bearing support force coefficients. Nonrotating benchtop tests show the influence of vibration amplitude, frequency, and damper cavity pressurization on force coefficients for two different viscosity fluids. Results indicate an increase in stiffness and a decrease in damping when increasing the frequency of excitation. Damper cavity pressurization was shown to eliminate squeeze film cavitation for the vibration amplitudes and frequency range in the study. Additionally, the paper advances a transient fluid–structure interaction (FSI) analysis aimed at gaining insight on the interaction of flexible elements bounding a hermetic fluid volume experiencing sinusoidal vibratory motion. The analysis considers an idealized damper model with and without a vibration transmission post while varying diaphragm modulus of elasticity for three excitation frequencies. Computational results were able to capture the increase in stiffness and the decrease in damping and show that the flexibility of the bounding elements influence the damper cavity volume change and phase ultimately affecting dynamic cavity pressures and force coefficients.
15 October 2018 in Journal of Engineering for Gas Turbines and Power
This paper presents a new gas bearing concept that targets machine applications in the megawatt (MW) power range. The concept involves combining a compliant hybrid gas bearing (CHGB) with two hermetically sealed squeeze film damper (HSFD) modules installed in the bearing support damper cavities. The main aim of the research was to demonstrate gas bearing-support damping levels using HSFD that rival conventional open-flow squeeze film dampers (SFD) in industry. A detailed description of the bearing design and functionality is discussed while anchoring the concept through a brief recap of past gas bearing concepts. Proof-of-concept experimental testing is presented involving parameter identification of the bearing support force coefficients along with a demonstration of speed and load capability using recessed hydrostatic pads. Finally, a landing test was performed on the bearing at high speed and load with porous carbon pads to show capability of sustaining rubs at high speeds. The component testing revealed robust viscous damping in the bearing support, which was shown to be comparable to existing state of the art SFD concepts. The damping and stiffness of the system-portrayed moderate frequency dependency, which was simulated using a 2D Reynolds-based incompressible fluid flow model. Finally, rotating tests demonstrated the ability of the gas bearing concept to sustain journal excursions and loads indicative of critical speed transitions experienced in large turbomachinery.
15 October 2018 in Journal of Engineering for Gas Turbines and Power
The following work advances a new concept for a hermetically sealed squeeze film damper (HSFD), which does not require an open-flow lubrication system. The hermetically sealed concept utilizes a submersed plunger within a contained fluidic cavity filled with incompressible fluid and carefully controlled end plate clearances to generate high levels of viscous damping. Although the application space for a hermetic damper can be envisioned to be quite broad, the context here will target the use of this device as a rotordynamic bearing support damper in flexibly mounted gas bearing systems. The effort focused on identifying the stiffness and damping behavior of the damper while varying test parameters such as excitation frequency, vibration amplitude, and end plate clearance. To gain further insight to the damper behavior, key dynamic pressure measurements in the damper land were used for identifying the onset conditions for squeeze film cavitation. The HSFD performance is compared to existing gas bearing support dampers and a conventional open-flow squeeze film dampers (SFD) used in turbomachinery. The damper concept yields high viscous damping coefficients an order of magnitude larger than existing oil-free gas bearing supports dampers and shows comparable damping levels to current state of the art open-flow SFD. The force coefficients were shown to contribute frequency-dependent stiffness and damping coefficients while exhibiting amplitude independent behavior within operating regimes without cavitation. Finally, using experimentally based force density calculations, the data revealed threshold cavitation velocities, approximated for the three end seal clearance cases. To complement the experimental work, a Reynolds-based fluid flow model was developed and is compared to the HSFD damping and stiffness results.
21 May 2018 in Journal of Tribology
The following paper focuses on an experimental and analytical study aimed at identifying the dynamic force coefficients of hydrostatic gas films for recessed flat plates. The motivation for the effort was brought upon by the necessity of generating more accurate models for hydrostatic gas films found in hybrid gas bearings. Pressurized air at room temperature up to 120 psi was used to test different recess geometries on a flat plate test rig, capable of characterizing the stiffness and damping force coefficients for varying supply pressures, gas film thickness values, excitation frequencies, and vibration amplitudes. The test rig design and operation is described. Experimental results include frequency-dependent stiffness and damping coefficients, and leakage. The test results show that using external pressurization can generate large stiffness values while exhibiting small leakage. However, the results also show that the majority of the test configurations portray high negative damping values. An analytical model is presented and numerical predictions are compared to experimental results. Example damping trends as a function of frequency, pressure, and film thickness are presented in addition to force coefficient plots as functions of pressure ratio.