This work comprises the selective deoxygenation of bio-derivable 3-hydroxydecanoic acid to either linear alkanes or secondary alcohols in aqueous phase and H2-atmosphere over supported metal catalysts. Among the screened catalysts, Ru-based systems were identified to be most active. By tailoring the catalyst, the product selectivity could be directed to either secondary alcohols or linear alkanes. In the absence of a Brønsted acidic additive, 2-nonanol and 3-decanol were accessible with a yield of 79% and 6% respectively, both of which can be used in food and perfume industries as flavoring agents and fragrances. To produce alkanes, we successfully synthesized a bifunctional Ru/HZSM-5 catalyst. The acidic zeolite support facilitated the dehydration of the intermediary formed alcohols to alkenes, while the following hydrogenation occurred at the Ru centers. Thus, full 3-hydroxydecanoic acid deoxygenation to nonane and decane, which are both well-established as diesel and jet fuels, was achieved with up to 72% and 12% yield, respectively.
Utilizing carbon dioxide (CO2) as a resource for carbon monoxide (CO) production using renewable energy requires electrochemical reactors with gas diffusion electrodes that maintain a stable and highly reactive gas/liquid/solid interface. Very little is known about the reasons why gas diffusion electrodes suffer from unstable long‐term operation. Often, this is associated with flooding of the gas diffusion electrode (GDE) within a few hours of operation. A better understanding of parameters influencing the phase behavior at the electrolyte/electrode/gas interface is necessary to increase the durability of GDEs. In this work, a microfluidic structure with multi‐scale porosity featuring heterogeneous surface wettability to realistically represent the behavior of conventional GDEs is presented. A gas/liquid/solid phase boundary was established within a conductive, highly porous structure comprising a silver catalyst and Nafion binder. Inoperando visualization of wetting phenomena was performed using confocal laser scanning microscopy (CLSM). Non‐reversible wetting, wetting of hierarchically porous structures and electrowetting were observed and analyzed. Fluorescence lifetime imaging microscopy (FLIM) enabled the observation of reactions on the model electrode surface. The presented methodology enables the systematic evaluation of spatio‐temporally evolving wetting phenomena as well as species characterization for novel catalyst materials under realistic GDE configurations and process parameters.
The use of gas diffusion electrodes (GDEs) enables efficient electrochemical CO2 reduction and may be a viable technology in CO2 utilization after carbon capture. Understanding the spatio‐temporal phenomena at the triple‐phase boundary formed inside GDEs remains a challenge; yet it is critical to design and optimize industrial electrodes for gas‐fed electrolyzers. Thus far, transport and reaction phenomena are not yet fully understood at the microscale, among other factors, due to a lack of experimental analysis methods for porous electrodes under operating conditions. In this work, a realistic microfluidic GDE surrogate is presented. Combined with fluorescence lifetime imaging microscopy (FLIM), the methodology allows monitoring of wetting and local pH, representing the dynamic (in)stability of the triple phase boundary in operando. Upon charging the electrode, immediate wetting leads to an initial flooding of the catalyst layer, followed by spatially oscillating pH changes. The micromodel presented gives an experimental insight into transport phenomena within porous electrodes, which is so far difficult to achieve. The methodology and proof of the spatio‐temporal pH and wetting oscillations open new opportunities to further comprehend the relationship between gas diffusion electrode properties and electrical currents originating at a given surface potential.
29 January 2023 in Advanced Materials Technologies
Microfluidic systems offer a multitude of advantages over classical techniques in the fields of biomedical and chemical research. Unit operations such as sample pre‐treatment, mixing, reactions, and especially separation and purification operations can be realized on microfluidic platforms enabling rapid prototyping and facile parallelization on the laboratory scale. However, the fabrication and integration of porous membranes in microfluidics poses several problems. Material development, membrane geometry, and membrane integration are three main questions to be addressed in this context. Herein, a durable and versatile method to anchor free‐form membranes with tunable microgeometry to surfaces, enabling the fabrication of stable, multi‐material microfluidic systems for different potential applications is shown. In addition, the influence of the macro‐ and microgeometry that is the shape and porosity of a membrane on key performance indicators such as diffusivity and permeation of tracer molecules is investigated. The presented characterization methods will enable a better understanding of microfluidic modules with incorporated membranes.