30 December 2021 in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
Due to the importance of the problems of implementing energy-saving technologies in modern conditions, one of the promising areas is the use of gas turbines for combined heat and power generation. One of the areas of effective development and technical re-equipment is the widespread use of highly economical combined steam and gas plants and gas turbines. The operation of the gas turbine unit “Aquarius” SE NPCG “Zorya-Mashproekt” with the injection of steam into the combustion chamber, which operates on the advanced cycle A-STIG and has in its circuit equipment for water regeneration, condensed from a vapor-gas mixture is considered. For condensation of steam from the vapor-gas mixture, a contact condenser-gas cooler is used, which is a mixing heat exchanger of complex design. The efficiency of heat transfer is determined by the design of the nozzle, namely, the developed heat transfer surface, small hydraulic supports, high heat transfer coefficients. An important aspect is the overall dimensions, which must be within certain limits. In the work it is offered to execute a design of the condenser in the form of a packed column. Different types of nozzles are considered to choose the best option. As a result of thermal design calculation of the contact capacitor, it is proposed to use Rashiga rings (15152) as a nozzle, which provide the lowest height of the nozzle at the required diameter of the device.
28 December 2025 in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
The article is dedicated to the analysis of the integrated operation of the VVER-1000 reactor and the PGV-1000M steam generator. It is intended to serve as a useful resource for students in mechanical engineering and thermal power engineering programs, providing material for analysis and reinforcement of knowledge in thermal calculations of power equipment. The reactor operation was investigated at varying volumetric power density values of the reactor core of 100, 110, and 120 W/m³. Based on the calculation and analysis of reactor operation, the optimal operating mode was selected, providing the highest efficiency while maintaining safe reactor operation at a volumetric power density of the reactor core of 110 W/m³. At this value, the temperature distribution in the fuel rod claddings along the entire length, the coolant temperatures at the reactor inlet and outlet, and the margin to critical heat flux were obtained. A detailed analysis of the temperature profiles showed that the maximum heat generation and the corresponding temperatures are observed at the center of the fuel rod. The study showed that the minimum CHF safety margin in the most heavily loaded channel exceeds 32.5%. This indicates that the CHF safety factor is above 1.325, which is considered sufficient for VVER-type reactors. Based on the reactor’s optimal operating parameters, a thermal design calculation of the steam generator was conducted to evaluate heat-transfer efficiency. To identify potential modernization opportunities, the effects of tube outer diameters (14, 12, and 10 mm) and primary coolant velocity on heat-transfer performance and steam generator dimensions were analyzed. A tube diameter of 10 mm and a primary coolant velocity of 5.72 m/s—corresponding to the optimal reactor value—were selected. These parameters ensure the most efficient heat transfer while maintaining safe operation of both the steam generator and the reactor.
29 December 2024 in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
The article is devoted to the improvement of the calculation methodology of air cooling systems and oil supply systems of gas turbine bearings by reasoned selection of boundary conditions and the structure of a homogeneous flow, which allows in the process of developing the support nodes of the engine rotor to determine the influence of geometric and mode parameters on the distribution of oil and the coefficient of heat transfer to the walls of the chamber, which forms an oil cavity. During the simulation, special attention is paid to the physics of the process, since a coolant with different properties can move in the channels of the cooling system, namely: liquid (oil), gas (air), or an air-oil mixture. If there is a two-phase substance in the channel, then the properties depend not only on the amount of gas content, but also on the orientation and geometric characteristics of the channels through which it flows.
28 December 2025 in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
The article reviews modern approaches to improving the efficiency of thermal schemes in power plants through the use of alternative working fluids and combined cycles. The limitations of traditional Rankine and Brayton cycles, which have reached the limits of optimization, are analyzed, highlighting the need for new technologies. Special attention is given to the Organic Rankine Cycle (ORC), the Kalina cycle, and the supercritical CO₂ (sCO₂) cycle, which enable effective utilization of low- and high-temperature heat sources. It is shown that the application of organic fluids, ammonia-water mixtures, and supercritical media can increase the overall efficiency of installations up to 50–60%. Combined systems (gas-steam, ORC+sCO₂) are examined as solutions for minimizing heat losses and improving design flexibility. Environmental and economic aspects are also discussed, including CO₂ emission reduction, integration with renewable energy sources, and participation in green tariff programs. The paper outlines development prospects such as wider adoption of sCO₂ cycles, creation of low-GWP working fluids, automation of combined systems, and enhancement of heat exchangers. The study summarizes current developments and trends shaping the foundation of high-efficiency and environmentally friendly energy technologies for the future.