The stabilization of lasers on ultra-stable optical cavities by the Pound-Drever-Hall (PDH) technique is a widely used method. The PDH method relies on the phase-modulation of the laser, which is usually performed by an electro-optic modulator (EOM). When approaching the 10−16 fractional frequency stability level, this technology requires an active control of the residual amplitude modulation (RAM) generated by the EOM in order to bring the frequency stability of the laser down to the thermal noise limit of the ultra-stable cavity. In this article, we report on the development of an active system of RAM reduction based on a free space EOM, which is used to perform PDH-stabilization of a laser on a cryogenic silicon cavity. A minimum RAM instability of 1.4 × 10−7 is obtained by employing a digital servo that stabilizes the EOM DC electric field, the crystal temperature and the laser power. Considering an ultra-stable cavity with a finesse of 2.5 × 105, this RAM level would contribute to the fractional frequency instability at the level of about 5 × 10−19, well below the state of the art thermal noise limit of a few 10−17.
After introducing noise radar probing of acoustic delay lines used as passive tags and sensors, we demonstrate the use of non-cooperative radiofrequency signal sources for such purposes in the context of passive radar measurement. A practical demonstration using IEEE 802.11n (WiFi) is given for a sensor operating at 2.42 GHz, solving the regulatory certification issue met when deploying dedicated radiofrequency emitters for short range radar applications. Furthermore, synthetic aperture radar measurement is completed by replacing the single surveillance antenna with a linear uniform array, solving the sensor collision issue when multiple targets are within range of the radar system.
2 November 2021 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
Progress made in optical references, including ultrastable Fabry–Perot cavities, optical frequency combs, and optical atomic clocks, has driven the need for ultrastable optical fiber networks. Telecom-wavelength ultrapure optical signal transport has been demonstrated on distances ranging from the laboratory scale to the continental scale. In this article, we present a Doppler-cancellation setup based on a digital phase-locked loop (PLL) for ultrastable optical signal dissemination over fiber. The optical phase stabilization setup is based on a usual heterodyne Michelson-interferometer setup, while the software-defined radio (SDR) implementation of the PLL is based on a compact commercial board embedding a field-programmable gate array and analog-to-digital and digital-to-analog converters. Using three different configurations, including an undersampling method, we demonstrate a 20-m-long fiber link with residual fractional frequency instability as low as 10−18 at 1000 s and optical phase noise of −70 dBc/Hz at 1 Hz with a telecom frequency carrier.
This article reports on the use of a Field Programmable Gate Array (FPGA) platform for local ultra-stable optical frequency distribution through a 90 m-long fiber network. This platform is used to implement a fully digital treatment of the Doppler-cancellation scheme required by fiber links to be able to distribute ultra-stable frequencies. We present a novel protocol that uses aliased images of a digital synthesizer output to directly generate signals above the Nyquist frequency. This approach significantly simplifies the setup, making it easy to duplicate within a local fiber network. We demonstrate performances enabling the distribution of an optical signal with an instability below 10−17 at 1 s at the receiver end. We also use the board to implement an original characterization method. It leads to an efficient characterization of the disturbance rejection of the system that can be realized without accessing the remote output of the fiber link.
We focus here on the optimization of a sensing system based on SAW resonators inserted in an oscillation loop for very high accuracy measurements. We use single-port SAW resonators built on AT Quartz, inserted in a Colpitts oscillator loop operating near 434 MHz. A reciprocal counter then is implemented on a FPGA platform which communicates the counting result to the ZigBee transmission system using an IEEE 802.15.4 protocol at 2.4 GHz. This system was tested by measuring the temperature of a climatic oven, revealing a measurement accuracy of a couple of 10 μK.
1 October 2019 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
Software Defined Radio (SDR) provides stability, flexibility and reconfigurability to radiofrequency signal processing. Applied to oscillator characterization in the context of ultrastable clocks, stringent filtering requirements are defined by spurious signal or noise rejection needs. Since real time radiofrequency processing must be performed in a Field Programmable Array to meet timing constraints, we investigate optimization strategies to design filters meeting rejection characteristics while limiting the hardware resources required and keeping timing constraints within the targeted measurement bandwidths. The presented technique is applicable to scheduling any sequence of processing blocks characterized by a throughput, resource occupation and performance tabulated as a function of configuration characateristics, as is the case for filters with their coefficients and resolution yielding rejection and number of multipliers.