25 June 2021 in IEEE Journal of Radio Frequency Identification
Metamaterials are artificially engineered novel substances (or matter) that exhibit properties not found in nature. One of the earliest examples of a metamaterial structure is the split-ring resonator. This article is a current review of metamaterials, what it is, its classification, and its applications towards the field of antennas and radio frequency identification (RFID) devices. There are two major types of metamaterial antennas: leaky-wave antennas, and resonant antennas. Antennas can be made from composite right-left handed metamaterials, or antennas can be loaded with a metamaterial screen such as a shelled electrically small antenna (ESA) fed by coax. Metamaterial resonators can aid in reducing the antenna size, help improve the gain, improve the directivity, improve the return loss, and control the radiation pattern (by loading the antenna with a tunable unit). Recent advances in printing and fabricating technologies have allowed for use of metamaterial antennas in wearable gadgets and textiles; and can be used in conjunction with RFID devices and tags to advance and aid (emergency) equipment used by first responders.
2 February 2021 in IEEE Transactions on Circuits and Systems II: Express Briefs
This brief demonstrates the performance of the first active bandpass filter to implement an active inductor in gallium nitride (GaN) technology. Fabrication of the filter and inductor was done using a 0.5 μm pHEMT GaN process with the system implemented on one 2 mm by 2 mm die. The tuning range of the active filter was measured to be 749 MHz at a centre frequency of 3.39 GHz with separate amplitude and quality factor tuning. An amplitude range for S 21 was measured to be from -12.2 dB to 13.7 dB within the operating frequency range. Taking advantage of the active inductor's negative impedance the filter was able to produce a quality factor of 138. On-chip, the active inductor occupies an area of 350 μm by 175 μm compared to approximately 350 μm by 350 μm for their passive counterparts of similar inductance (a 50% decrease in size). The filter was designed for LTE/WLAN applications to demonstrate the capabilities of the active inductor.
19 October 2022 in IEEE Open Journal of Antennas and Propagation
In this paper, the impact of amplitude and phase imbalance on a proposed dual differential fed patch antenna is analyzed in the context of system effective reflection coefficient and axial ratio (AR). A single square patch with four ports is used as a solo radiating element and provides absolute symmetry at radiating. An in-depth analysis will be presented to understand the impact of external RF chain components on the performance of the proposed antenna. When fully differential excitations and perfect symmetry can be achieved, all six polarization states exhibit identical system effective reflection coefficients with close to ideal AR for CP. When phase imbalance and amplitude imbalance only exist in between the two differential pairs, the antenna system matching performance is found to be unchanged. In the presence of the feed network, circular polarization (CP) achieves a measured maximum AR of 0.49dB along the antenna pointing angle, while linear polarization (LP) has a measured maximum cross polarization of −30dB. This work monitors the beamwidth over which the AR can be kept below 1dB (BW-AR−1dB). Based on the optimization of phase imbalance, a novel BW-AR−1dB enhancement technique is introduced. Compared to the case with better AR at the main beam location, an improvement of 14. beamwidth is measured without significant degradation of AR. Isolation better than 40dB across an operating frequency of 9.27 – 9.4 GHz has been experimentally demonstrated for the proposed dual differential fed technique. The resulting antenna is compact and low profile which is an appealing candidate for phased array applications.
21 August 2019 in IEEE Transactions on Circuits and Systems II: Express Briefs
This paper analyses linearity of LC DCOs using a new tool: topographical linearity field maps. The analysis in this paper assesses whether given combinations of LC will produce good linearity. The paper then shows how to apply the analysis in the design of the DCO using the field maps. The DCO in the paper had a max DNL of 0.280 LSB and max INL of 0.645 LSB. This was achievable by taking advantage of an LC core’s inherent nature. The measurements indeed confirmed that the analysis technique presented is valid.