31 December 2018 in Eksploatacja i Niezawodność – Maintenance and Reliability
The aim of the article is to develop new methods of analysis, estimation and optimal selection of quantitative resources (inherent and non-inherent) in the planning of the product effect for specific environmental conditions. The required iterative approach in the construction of the mathematical model and analysis of its possible practical applications and search for how to figure those opportunities. As the testing method has been applied method intuitive, allowing you to use the experience of expert analysis from ongoing opportunities to make full use of the sustainability properties and customize to their processes. The results were presented in the form of mathematical models in the collection of complex numbers and graphically on the plane of complex numbers. Method to estimate changes inherent and non-inherent resources objects (machines, systems, organizations) on their productivity (Po). The method uses the original, innovative, model potential workspace object (PrO) in the form of a complex binding numerically inherent (Zi O) and non-inherent (ZniO) resources objects. Evaluation of value Po it was proposed with the PrO. The values of the Zi O and ZniO was adopted as two independent resources constituting the whole of resources in the required in the production (or in the service). Method evaluation Po illustrates for the resources object described model Ro =│PrO = f (ZpO, ZoO)│, where Zi O is a work resource (ZpO), ZniO is extracted from the operation of the resource service (ZoO), and the generating capacity of the object Po is described using a pointer named R object (Ro). Illustrated in the complex plane analysis results and the results obtained from the calculation PrO and Ro, for contract values of the ZpO and ZoO, indicate the application capabilities developed method. Method allows a very clear description of the productivity changes objects (or processes, or production organization), in the context of the selection of manufacturing resource structure, through the separation of the factors causing these changes. Method can be adapted for optimal production costs (or services) through design changes object and/or design changes of the process exploitation. Developed the method brings new opportunities for theoretical and application in relation technical and economic sciences.
30 June 2019 in Problems of Mechatronics Armament Aviation Safety Engineering
This paper presents an outline of a method of optimising the service life of aircraft guns at the stage of design engineering and retrofitting. The essence of this method is a selection of service lives and quantities of preventively replaced components and the service parts of non-reconditionable components resulting in an overall reduction of gun production and operating costs (including the costs of replacement parts stocks) with an improvement of the service life of the whole gun assembly. The method assumes that the service lives to be selected must meet a criterion of predefined reliability, maximum service availability when installed aboard a combat platform (i.e. an aircraft) and the minimum time to re-use. It is pointed out that in the design engineering of preventive component replacement and the assessment of the gun selection, a criterion of total gun cost reduction shall apply; the total gun cost is construed as the cost of production/purchase and maintenance applicable to the operating mode (with the costs and time to provide replacement parts). The total gun cost should be decisive in the definition of service lives and the number of components in preventive replacement. To analyse and select the service life and the MTBR (Mean Time Between Replacements), examples of reliability and life models of guns were developed in reference to the applicable operating standards and changes in total costs. This was followed by a demonstration of an innovative model of mapping gun (production/purchase and operating) costs with a complex number plane. The method presented herein facilitates analysing and assessing the feasibility for improvement of a gun’s availability in combat field and training operations.
30 September 2019 in Problems of Mechatronics Armament Aviation Safety Engineering
The article presents a concept of the procedure for researching the dynamic properties of the multi-wire springs used in NR-30 guns. The aim of the research was to check the possibilities of determining the limit values of the flexibility of the multi-wire springs for the NR-30 gun, as well as to verify the obtained research results using those from range and static tests (after long compression). While verifying the method (selected measurements of 4 springs with varying degrees of wear), static and dynamic compression tests were performed on a spring mounted on a gun on specially prepared testing stations. The description of the data measurement and acquisition method applied should be considered an important element of the description of a testing station. Based on the obtained research results, it has been inferred that, during the striker’s backward movement, wave phenomena likely transpire in the spring. Force value fluctuations taking place during the spring’s movement are visible in the obtained diagrams. The dynamic and static test results (on springs with varying degrees of wear) allowed the authors to evaluate the impact of a multi-wire spring’s wear on the value of its force of interaction with the automation elements of an NR-30. Based on the data obtained, the assumptions for the method of evaluating multi-wire springs’ durability and using it to evaluate the suitability of a given spring type for use according to its technical state, have been elaborated. The final determination of the limit values of the springs’ parameters requires further research using a station with an ammunition belt encumbrance emulator, as well as emulation of the overloads of the kinematic arrangement of the gun while airborne.